- Home
- 79096022400
- Instructions
79096022400 Kenmore Wall Oven - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Above 400 beeper went off & code numbers came up on read out
78 of 89 people
found this instruction helpful.
-
Russell from Lake Havasu, AZ
- Easy
- 30 - 60 mins
-
Nutdriver
Cut off power at fuse panel. pulled stove out from wall went behind stove removed back panels in area of sensor that I could see from the front side, inside oven. Located sensor from rear & unpluged senser from wiring bundle reached inside oven & removed screws from sensor. Pulled sensor out & threaded wire through hole. Took old & new
... Read more
sensors to bench in shop. Plug on new not the same as old. Had to change plug Cut and stripped wires. Wire is very small, need to use a good stripper. Twisted wire together & soldered connection, used shrink wrap to insulate wire. Took part inside and reinstalled in reverse order. Used 1/4 inch nutdriver on total job start to finish.
Read less
Was this helpful?
Thank you for voting!
Oven wouldn't operated. Error code F9
76 of 101 people
found this instruction helpful.
-
Richard from Centennial, CO
- Really Easy
- Less than 15 mins
-
Nutdriver
I called a repair place. They charged $54 to diagnose, (said it needed a new latch motor) then wanted $220 to complete the repair. I checked online prices and did it myself for about 15 minutes work and the latch motor itself ($44?).
Was necessary to uplug the range, pull it away from the wall and remove the back panel sheet m ... Read more etal, then 3 screws that mount the motor. Replace motor, reattach sheet metal. Plug in. Done. Ready to bake cookies.
Was necessary to uplug the range, pull it away from the wall and remove the back panel sheet m ... Read more etal, then 3 screws that mount the motor. Replace motor, reattach sheet metal. Plug in. Done. Ready to bake cookies.
Read less
Was this helpful?
Thank you for voting!
burned out burner
70 of 99 people
found this instruction helpful.
-
Lori from Winter Haven, FL
- Easy
- Less than 15 mins
-
Pliers, Screw drivers
First we removed two screws under the rim of the range top to open the lid. Lifted the lid and removed the screws from the bracket that holds the elements, Be careful with the clips that hold the element in, if you break them or bend them there aren't any more! Also note which holes they were in, they are marked according to the differ
... Read more
ent sizes of elements. Disconnected the wires, needed needlenose pliers to grip them...connected new element, popped it back in place, replaced bracket, closed top ...Easy peasy!!!
Read less
Was this helpful?
Thank you for voting!
Oven light receptacle broken - bulb base broke off
69 of 118 people
found this instruction helpful.
-
Paul from Spokane Valley, WA
- Easy
- 30 - 60 mins
-
Screw drivers
Turned power off at electrical panel. Pulled oven away from wall. Removed back cover (6 screws), then unplugged wires from old receptacle. I had to pull the squeeze clips backwards & break them to remove the old receptacle - couldn't squeeze them enough to remove them otherwise. The old receptacle came out through the inside of the oven,
... Read more
and the new one snapped in easily from inside the oven as well. Replaced wiring, installed new bulb, restored power & tested. Replaced back cover. Good time to vacuum under/behind where the oven usually lives before sliding it back to the wall.
Read less
Was this helpful?
Thank you for voting!
9" radiant burner element stopped working.
46 of 54 people
found this instruction helpful.
-
STEPHEN from GREENBUSH, ME
- Easy
- 30 - 60 mins
-
Pliers, Screw drivers
VERY IMPORTANT! kill the circuit breaker to the unit and/or unplugged it! 2 screws hold the ceramic glass top to the lip @ top of oven--remove them and the top can be lifted up to expose all the burner elements and wiring--remove the 2 end screws that hold the retainer bracket for the burners - then remove the 2 screws that hold the burne
... Read more
r in question to the bracket-there's also a retainer pin that needs a bit of fussing with to completely free the burner--once totally free remove the wires from the bad unit to the good unit exactly as they are situated --install new unit onto bracket with screws and bracket back to its original location on the ceramic top-put top back down and replace both anchor screws--initiate power back to unit and yeeehahh--You just saved yourself lottsa money from repair bills!!!
Read less
Was this helpful?
Thank you for voting!
right front element burned out
45 of 53 people
found this instruction helpful.
-
Larry from Wenatchee, WA
- Easy
- 30 - 60 mins
-
Pliers, Screw drivers, Socket set
FIRST I UNPLUGGED THE GLASS TOP RANGE. While locating the part on the PartSelect diagram I was also able to determine how to access the burned out element. It was very simply to remove three phillips head screws in the front top( above the oven)area of the range, slide the topof the range forwardand lift it up, remove one screw holding th
... Read more
e metal bar under the element, replace the element by usinga a pair of pliers to remove the electrical wires and then reversed the process. I saved a tidy amount doing the job myself.
Read less
Was this helpful?
Thank you for voting!
oven door would not stay closed tightly lost of heat
42 of 45 people
found this instruction helpful.
-
Barbara from Lagrange, IN
- Easy
- 1- 2 hours
-
Screw drivers
I replaced the door hinges and put a new handle on the oven door. I can not remember what was done exactly because I had a 2 and 4 yr old helping me. But I can tell you that the instructions included with the kit made the job easy. There were a few problems with the type of bit used to get the screws off (I needed a star type of bit, b
... Read more
ut used my phillips because that's what I had on hand). It worked fine, but it would have been better with the star tip screwdriver. There were helpfull hints that told me to prethread the new screws going into the oven door and frame. That was a big help instead of trying to hold the part and start the self threading screws. All in all I would order the parts again and attempt to do another repair on my oven, because it saved me a lot of money. Good luck to all the other first time repairers out there.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
burner would not heat
19 of 24 people
found this instruction helpful.
-
Ed from Winthrop, MA
- Easy
- 1- 2 hours
-
Screw drivers, Socket set
killed the 50 amp power. removed 3 screws from above oven door slid out cook top, dropped brace holding 2 front burners. The connector corroded off had to look for a high heat connector to connect to the element, after that just screwed everything back together.
Was this helpful?
Thank you for voting!
No heat when turning oven on.
18 of 23 people
found this instruction helpful.
-
Joseph from Edgewater, FL
- Easy
- 15 - 30 mins
-
Nutdriver
Started by replacing element which was clearly broken. Still no heat. So then I changed the oven sensor. Was disappointed that when I received the sensor I had to cut and splice the connector that was on it with the old one that came off the old sensor. Did that and still no heat so I had to buy a new clock/timer. Went to another store fo
... Read more
r that because of the connector not being the right type and there was no picture of the clock/timer like the other website. Overall ok, normall troubleshooting steps, just wish I didn't have to cut and splice the connector on the new sensor I purchased from here.
Read less
Was this helpful?
Thank you for voting!
One element in a glasstop range would not engage
17 of 21 people
found this instruction helpful.
-
Kwok from Silver Spring, MD
- Really Easy
- 15 - 30 mins
-
Nutdriver, Socket set
All of a sudden, one element in our glasstop range would not light and heat up. My wife and I were not sure what to do. Looked it up on the internet, found that you can do it yourself as others desribed the process of accessing the elements below. We decided to do that. It takes two people as one is holding up the glass because it ope
... Read more
ns like a car hood. While we diagnosed it was not a wiring issue (found a burnt wire, rewired the burnt wires (after mending the non burnt portions) to another element. The element that was not working before still did not turn on. Decided to purchase an element. While many online places sell elements, PartSelect actually allowed searching by brand with exploded views of the range to select the exact parts. This lessened the worry of purchasing a wrong element. When the part came (almost one day later), the repair was less than five minutes. Thank you PartSelect. I feel I saved a lot of money and aggravation.
Read less
Was this helpful?
Thank you for voting!
Oven Door could not close tightly
14 of 16 people
found this instruction helpful.
-
Frank from Gwynn Oak, MD
- Really Easy
- 30 - 60 mins
-
Screw drivers, Wrench set
My problem with the door was a bit serious because not only would I lose heat from the top of the door, but could not use the convection oven unless the door closed tightly.
However, the repair could not have gone easier. The instructions were very simple and totally accurate. I would suggest that anyone doing this job with a ... Read more door that has full glass across the front should have a helper neaby. The door is quite heavy.
This probably the easiest repair job I have ever done, and I have done many.
However, the repair could not have gone easier. The instructions were very simple and totally accurate. I would suggest that anyone doing this job with a ... Read more door that has full glass across the front should have a helper neaby. The door is quite heavy.
This probably the easiest repair job I have ever done, and I have done many.
Read less
Was this helpful?
Thank you for voting!
Connection to surface element was broken
17 of 27 people
found this instruction helpful.
-
javier from oceanside, CA
- Easy
- 30 - 60 mins
-
Screw drivers
I went all the way around the unit and removed screws holding top of unit in place. Removed knobs holding front panel in place. Remove control panel. top should come off. Remove screws attaching element top and metal frame. Undo bracket and remove element. Disconnect wires. Remember where they were attached.
Replace element and rever ... Read more se steps.
Replace element and rever ... Read more se steps.
Read less
Was this helpful?
Thank you for voting!
Burner failed due to poor manufacturing quality
13 of 17 people
found this instruction helpful.
-
LaVern from Cedar Falls, IA
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers
Disconnected power. Removed hold down fasteners for stove top. Fortunately, I did not flue down or use the double back tape to secure stovetop to counter. If this adhesive were used, it is possible I would have had great difficulty in removing range. I did not disconnect the wiring, but turned the range top over to access the cover.
... Read more
I removed the cover and easily removed the failed burner and installed the new ones. I had to pull 4 wires from the terminal strip and reattach them. The hold down strap for the burner was reinstalled. Range top turned back over and fastened down. Back in service.
Read less
Was this helpful?
Thank you for voting!
oven door would not close all the way
11 of 12 people
found this instruction helpful.
-
Cheryl from Wellsburg, IA
- A Bit Difficult
- 30 - 60 mins
-
Screw drivers
Removed the door and the inner panel of the door and replaced the hinges. Replaced the screws and put the oven door back on. It closes tight now just like new. I have now ordered the replacement cap so my oven looks like new again.
I only have one suggestion to make the installation easier. If the manufacturer would preth ... Read more read the holes in the new parts, it would save time from having to prethread the holes with the screws, prior to installing them.
I only have one suggestion to make the installation easier. If the manufacturer would preth ... Read more read the holes in the new parts, it would save time from having to prethread the holes with the screws, prior to installing them.
Read less
Was this helpful?
Thank you for voting!
Front Right Radiiant burner was damaged
12 of 17 people
found this instruction helpful.
-
Rashiklal from Marietta, GA
- Really Easy
- 1- 2 hours
-
Nutdriver
Followed the instruction printed on the page, while ordering the part.
Was this helpful?
Thank you for voting!