79095929302 Kenmore Range - Instructions

This was the first time replacing the fan. It is a lot easier to work in the oven compartment with the oven door removed, only two screws on the door and the hinges were released. I found that a couple of the screws were either rusted or stripped so I used a pair of pliers to remove the screws that were holding the diffuser in place. O ... Read more nce there was access to the fan I found that the fan was warped and that the blades were scraping against the back wall of the oven. The next challenge was to remove the retaining nut. I used a sheet metal screw to secure the warped fan to keep it from spinning. once I figured out that you have to turn the retaining nut to the right to loosen, it came off easily. 1/2" socket with extension. When I replace the fan I used two washers for spacers to make sure that the fan would not scrape the wall of the oven. Its been tested many times and the oven does not make that horrible sound anymore.

I went all the way around the unit and removed screws holding top of unit in place. Removed knobs holding front panel in place. Remove control panel. top should come off. Remove screws attaching element top and metal frame. Undo bracket and remove element. Disconnect wires. Remember where they were attached.
Replace element and rever ... Read more se steps.

Disconnected power. Removed hold down fasteners for stove top. Fortunately, I did not flue down or use the double back tape to secure stovetop to counter. If this adhesive were used, it is possible I would have had great difficulty in removing range. I did not disconnect the wiring, but turned the range top over to access the cover. ... Read more I removed the cover and easily removed the failed burner and installed the new ones. I had to pull 4 wires from the terminal strip and reattach them. The hold down strap for the burner was reinstalled. Range top turned back over and fastened down. Back in service.

Disconnected power at breaker. Removed cooktop mounting screws, lifted top and propped in up position. Removed two screws and lowered two front burners mounting frame. Wiggled dual element free at the clips and proceeded to swap wires one at a time and realized the difference with connectors 1a and 2b much later when only the center porti ... Read more on was heating up. Finally figured out the problem and everything works as advertised. Pay attention if you own a Kenmore product.

Slide out the old; slide in the new!

Followed the instruction printed on the page, while ordering the part.

Self easy

PS Great service Super FAST.
Thanks Jesse

Followed on-line instructions to remove the defective heating element. Some connection tabs on the replacement unit were different than the original. One tab was too wide to accept the stove's slip-on wire connector without fling down the tab width on the heating element. Thanks to some on-line instructions, wire connections to element 1a ... Read more and 2a had to be reversed. If not for those instructions I would probably have ended up sending the unit back to the supplier, as an incorrect replacement !

My husband followed the video instructions and it was easy to fix.

found your website ,asked the question, got an answer, recieved a diagram and a possible problem diagnosis. obtained the part threw PartSelect quickly. took the knob off unscrewed two screws out ,disconnected the terminals and reconnected to new switch put the two screws back in and put the knob on!!! thanks ncountry "

Slid oven out removed one screw one plug replaced part took 5 minutes.told parts repair the error message and they sent me the correct part in two days will use them again saved me from Repair man wanted 85 dollars just to look at it my cost was 28 for probe and 8 dollars for shipping already helped neighbor with their stove they needed n ... Read more ew ignighter 12 dollars repair place want 110 to come look at it this site walks you through repair best service!!!!

Twisted replacement bulb into place easily. Let there be light!

Went very well and it works!

Removed two screws in over pulled out part took off wires and put them on new elememt

The hardest part was pulling the oven away from the wall. Two bolts hold the sensor in place and a clip connects the electronics. Replacing the old one was trivial.