79095882301 Kenmore Range - Instructions

Very simple, just removed three screws and pulled the top out and turned over and then removed the two screws holding the support bar. Removed and installed the element.Surprised to see that the element burned out in such a short time.

Replaced temp probe and checked OK. This model did not have a full back as the instructional video showed. No cover to remove at all. Only suggestion might be to include two wire nuts of proper size. Average wire nut would be too big. Fortunately, I happened to have a couple.

1. Remove the old Trim by opening the door and unscrewing the two top screws holding the trim and glass to the door. 2. Lift the trim piece off of the glass, being careful as the glass will be a bit loose, and unscrew the handle from the trim piece, discard those two screws. 3. Place the new trim piece on the glass so that it fits snugly. ... Read more 4. Place the screws back through the holes on the inside of the door, through the new trim piece and attach them to the handle. 5. Tighten down snugly and close door. You are done!

I just installed the extra rack and re-arranged the existing ones. Works great!

Unscrewed the old element (2) screws, then unscrewed the (2) brackets holding the element up, pulled the element out of the back wall of the oven unhooked the (2) electrical wires and left them hanging. Installation is in the exact reverse order.

open door,throw the door latches at the hinges and remove door. Take the out of the outer panel so you can separate the glasses. remove clip that hold the outer glass in place. I ordered a replacement glass as I never thought that it would come clean it looked so bad, but it cleaned up like new so I now have a spare glass for my oven door ... Read more . Just reverse the way you take it apart to put it back together.

Easy to put in but i droped a screw to hold the element. had to pull another screw to fix it

simple, removed a few screw's, unplugged old burner, plugged in the new one. that was basically it. easy!

Checked the burner and no power to heat the burner. removed the old switch and put on the new one.

Would have been simple if Frigidare had not changed the plastic snap wire connector on the part. The replacement part had a different snap together wire connection. After a couple of phone calls stating that the new part and the old part had different part numbers was informed that you have to snip off the ends and use wire connects but ... Read more it was the right part. Once I knew that it was a simple repair if you have the wire connects to connect the wires.

I bought the clock/timer board from Part Select. After receiving the part I open the back panel of the clock/timer and replace the board. I took out the wires one after the other and replace the wire one at a time until I finished replacing all wires. I went to the garage and switch on the breaker switch for the range and everything works ... Read more well so far. I'm not sure though if the clock/timer that I purchased from Part Select includes the fix to the flow.

Took door apart, went online to partselect, ordered new glass, and put it back together. Oven looks like new. Makes sense to order the isolation as well when you do the repair

Timer was bad. Removed the four screws on the rear panel, and then the four screws holding the timer in place. I let the old one dangle by the wires until the new one was in place, then just switched the wires one at a time. There is one set that has a plastic connector, and you need a small flat screwdriver to depress the locking tab on ... Read more the top of the connector to release it. Be sure and order a new face plate as the old one will not come off without tearing. Re-install rear cover and your done.

Pulled stove away from the wall and unplugged it. Removed probe and cut the wires because the connection clip on the new probe was different from the original. Leave the wires as long as possible because you will need the extra length to splice the clip from the old probe to the wires on the new one. Replaced probe and plugged the oven ba ... Read more ck in. Done.

replaced temp probe per your suggestion. No improvement! checked both heating elements with ohm meter. OK Next suggestion was replace circuit boards. Bought new range for less than cost of 2 oven/range control boards.