79095660100 Kenmore Range - Instructions

Flip up top, remove wires and two screws. Replace in opposite way. Turn off power to stove first.

First my husband cut off the circuit breaker. He then removed the two screws that held the element in place and pulled the element out about 3 inches and disconnected the two wires. The rest was easy. We were impressed at how fast the element was sent. We were told about 5 days to 7 days. The element arrived on the second day. Very p ... Read more lease with the service and the product.

I was selling my home and did not realize that the anti-tip bracket was not originally installed. A home inspection caught the problem and the buyers required that I install one. I could not find the original and obviously the installer never put it in place to begin with. The buyers wanted this resolved within a week so I had to act f ... Read more ast. I could not find one locally so I found what I needed on your website. It arrived in a couple of days and was easy to install. I used the template provided in the kit and drove the screws through the bracket into the wood plate behind the drywall. Pushed the range back in place and that's it. Couldn't get any easier.

First I removed 2 screws that held the stove top in place. Raised the stove top and support it. Then, I removed the hold down spring for the burner and removed three wires from the old burner. I found that the connector on the white wire was spread open too much so I crimped it closed for a better fit on the terminal. I reattached the thr ... Read more ee wires, put the hold down spring back in place, lowered the stove top and installed the 2 screws. JOB DONE

shut off breaker to appliance or unplug

remove oven racks

unscrew lock tabs at back of oven

disconect wires on both sides

discard old element reconnect new element
screw new lock tabs back in.

turn on power test oven.

Had to reference original owner's manual for instruction(s) on how to remove oven door. Used several "YouTube" videos to reference oven door design (Oven door glass is actually several layers of glass.) After completing about 30 mins of research and finding the right square drive bit, the repair went smoothly and without complications. Th ... Read more e biggest challenge was researching and understanding what part(s) were needed and how to replace them. It seemed liked a lot of work doing the research however it sure beat a $350 repair bill. It cost me $90 and about 1 1/2 hours of total time. Oven works better than ever, thanks parts select for the part(s) and diagram(s) ...

Lifted the oven top, removed the controls cover, slipped the lens into the hole and slid the light holder device onto the lens

order pcs fit perfect.

Removed the broken door handle with a screwdriver, replaced the new door handle with a screwdriver. Took less than a couple of minutes to make the repair.

i first replaced element after old smoked & quit. replaced switch but i noticed when i started to replace the wires one at a time something didn't seem right. after checking the #s on the old one, they didn't match up with the new one.luckily i had the stove diagram from a packet on the back of the stove. i traced each wire according to ... Read more the diagram and everything worked out fine. i'm just glad i didn't replace each wire to wire.the #'s were on the switch where each wire went which was different than the org. even though they looked the same.

Removed the one remaining drawer guide and stared at it for 10 minutes trying to understand where it came from and how it worked. Looked it up on partselect.com. While there was no part number, the detailed photo on your web site was enought to assure me that you had the correct part. Ordered them in a few moments and three days later ... Read more I had the parts. The hardest part of the job was trying to understand how to install the widgets. After 20 minutes to crawling around in the stove's inards, I finally got the "aha" and the drawer on this antique stove was finished. Thanks! Couldn't have done it without you.

Disconnected power at breaker. Removed cooktop mounting screws, lifted top and propped in up position. Removed two screws and lowered two front burners mounting frame. Wiggled dual element free at the clips and proceeded to swap wires one at a time and realized the difference with connectors 1a and 2b much later when only the center porti ... Read more on was heating up. Finally figured out the problem and everything works as advertised. Pay attention if you own a Kenmore product.

Slide out the old; slide in the new!

New part arrived, opened pkg. , Pulled drawer out. . . Snapped in new parts. . . . Done!! Saved myself $100. 00.

Self easy

PS Great service Super FAST.
Thanks Jesse