79095652000 Kenmore Range - Instructions

I tried to operate the rocker switch which switches from one element to two or vise versa. There was no resistance on the switch. I fiured it was defective. After I received the switch from Partsselect, I pried the old one out , remove the two wires, which were attached to the switch by spade terminals. I re-attached the wires to the new switch and pressed it, by hand, into the reage
console.

I had to replace the switch on one of the large elements. It could and should have been a quicker repair if there would have been some installation/wiring instructions included with the part. Other than that the repair went well.

The simplest repair ever! I just snapped it in and put the drawer back - fixed. I hope I have other repairs this simple.

after pulling away from wall and unplugging remove 5 screws in upper back panel lift off being careful of sharp edges if part of lens is still in hole push it out towards the front insert lens from front of unit slide light assy over pin on back of lens replace back panel plug in range push back against wall check for level you're done

Your website is great...easy and it literally took me no mote than 5 minutes to find what I needed and order...and received it VERY quickly. Must say I was dreading going to some parts house that we have in our town in bad area, and searching on dusty shelves for what I needed...am so glad I found you!!

was easy open the back side of the range and change the part, the only issue was the wire I used the diagram

I removed the oven door using a phillips screwdriver. It was very easy because I didn't have to worry about the door hinges springing the door back. I'm not really handy and it went very easy.

first thing was to turn the breakers off. then pull the range away from the wall. used an 1/8 th inch socket to take off the back panel to get access to the switch.used a Phillips screwdriver to disconnect the switch under the knob in the front. took off the wire terminals one at a time and matched it to the numbers on the old switch.replaced the knob, screwed it on to the range. turned the breakers on and tested the switch.worked fine, replaced the back cover and pushed it back into place.

First, I read about the experiences of others who did this repair.

Then I removed the oven door by removing the single screw at each hinge - visible when the door is open - using a #2 Phillips screwdriver (the only tool needed for this repair). I placed the door on the kitchen table and removed the two screws at the inside top of the door - they also hold the handle onto the door.

I placed the four screws removed from the inside corners of the door -- into one corner of a tray I used to hold the parts in order. Then I removed the eight screws from the perimeter of the door and placed them into another corner of the holding tray. Then I turned the door over and removed the outside part of the door from the inside - as in removing the cover from a box.

Then I removed four screws holding the middle and outside glass panels and placed them in another corner of the parts tray. Then I removed two screws holding the steel panel against the glass. Then I removed the broken glass from the bottom of the tray. That's when I discovered I had ordered the wrong glass panel.

I called the PartSelect number to return the glass, and while discussing how to return the part, I asked if I had to call another number to get the correct part. The lady assured me she could process my order for the correct part. She was very knowledgable about the system and quickly found the correct part from the schematic. I received the replacement part 24 hours later and installed it within 20 minutes.

Overall a success story. Excellent service and easy work.

Unplugged range from wall plug, popped toggle out with screwdriver, unplugged wire ends, reattached to new switch and snapped in place.
Removed 9 screws from back of stove to remove broiler wires, removed wire racks from oven, used square driver to remove mount screw, removed old element and replaced with new, reinstalled all screws, plugged her up and tested. WORKS LIKE A NEW ONE !

Remove drawer. Insert new slide. Install drawer.

Sat on floor, pulled drawer out, inserted new clips, remounted door, stood up, high-fives myself.

Removed old switch, moved the one wire to the same pin on new very cheaply made but expensive made in Mexico switch, replaced switch, pugged range back in too AC, operated new switch, created sparks and smoke. Element now glows to max immediately when turned on. Replaced stove problem gone!

I removed the four screws holding the element in place and pulled the element out and disconnected the two wire. Installation was pretty much the reverse of the removal except, when I went to put the two screws holding the element to the top of the oven I discovered the holes were rusted out. I looked for inserts to put in the holes but every time I tried different inserts the holes got bigger. I finally realized the oven is just sheet metal so I moved the bracket about an inch drilled new holes and used self-tapping screws.

Replaced infinite control very easily.