- Home
- 79095652000
- Instructions
79095652000 Kenmore Range - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Overlay was cracked, drawer glide missing
14 of 20 people
found this instruction helpful.
-
Michael from Anchorage, AK
- Really Easy
- Less than 15 mins
-
Nutdriver, Screw drivers
Overlay replacement is easy; 1st remove two screws that hold panel to top of stove (philips screwdriver) and lift up off of lip at very top, 2nd remove two screws that hold control to panel (nutdriver or square drive screwdriver), 3rd peel old overlay from control panel face (make sure you get any & all little bits so new overlay sits flu
... Read more
sh), 4th peel backing from overlay and position over control panel (peel protective film from face of overlay as well), 5th reposition control panel and reinstall two screws removed in step two above, lastly reposition top panel on stove and reinstall the two screws removed in step one above.
Drawer glide just snaps into place on the lower rear corners of drawer, then you slide drawer back into place.
Drawer glide just snaps into place on the lower rear corners of drawer, then you slide drawer back into place.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Oven Racks needed to be replaced.
11 of 14 people
found this instruction helpful.
-
Peter from Chicago, IL
- Really Easy
- Less than 15 mins
Slide out the old; slide in the new!
Was this helpful?
Thank you for voting!
Broiler element burned out
10 of 11 people
found this instruction helpful.
-
Merlin from Newport News, VA
- Easy
- 15 - 30 mins
-
Pliers, Screw drivers
Very important first step: Turn off the circuit breaker for the range or disconnect the power cord.
I removed the oven door to make it easier to access the back of the oven; remove two screws and the door lifts off of the brackets. Removed a screw from the top of the oven that secures one end of a wire that supports the broil eleme ... Read more nt. Removed two screws that secure the broil element plate to the back of the oven. Pulled the element forward exposing the end terminals and wires. The wires are connected to the element by spade connectors. Used long nosed pliers to remove the connectors from the element. Pushed the connectors on to the new element and stuffed the ends of the element and wires back through the opening and the insulation. Reinstalled the two screws holding the element in place and the screw holding the wire in place across the top of the oven. Reinstalled the door. Took less than 30 minutes.
I removed the oven door to make it easier to access the back of the oven; remove two screws and the door lifts off of the brackets. Removed a screw from the top of the oven that secures one end of a wire that supports the broil eleme ... Read more nt. Removed two screws that secure the broil element plate to the back of the oven. Pulled the element forward exposing the end terminals and wires. The wires are connected to the element by spade connectors. Used long nosed pliers to remove the connectors from the element. Pushed the connectors on to the new element and stuffed the ends of the element and wires back through the opening and the insulation. Reinstalled the two screws holding the element in place and the screw holding the wire in place across the top of the oven. Reinstalled the door. Took less than 30 minutes.
Read less
Was this helpful?
Thank you for voting!
burned double element
29 of 69 people
found this instruction helpful.
-
Bartolino from Ormond Beach, FL
- Easy
- 15 - 30 mins
-
Pliers, Screw drivers
I must say that I am very pleased with speed of your part delivery, I have to ad that the first part I received was defetive, the inner element was open and therefore it was not working, I called back and a very curteous person took care of the problem, I got a replacement part 2 days later and now all is OK.
Very good service indeed ... Read more ,
Thank you.
Very good service indeed ... Read more ,
Thank you.
Read less
Was this helpful?
Thank you for voting!
The temperature was irratic the entire time the stove was on. I would set it for 350 and it would go up to 425 then down to 275. It was all over the place.
9 of 10 people
found this instruction helpful.
-
Jenifer from St. Marys, WV
- Really Easy
- 30 - 60 mins
-
Pliers, Screw drivers
It was great. We ordered the part, it was shipped the next day and I had it the day after that. It was easy to install and the stove has worked perfect since. Color us happy!
Was this helpful?
Thank you for voting!
F3 Error
10 of 13 people
found this instruction helpful.
-
Jonathan from Lewisburg, PA
- Really Easy
- Less than 15 mins
-
Wrench set
I removed the back panel, about 6 screws, then found the probe which was attached by 2 screws. Unscrewed them and unplugged it. Plugged the new one in and replaced all the screws. The oven works like a charm now! No more F3 errors!
Was this helpful?
Thank you for voting!
Draw Glide Broken Off Bottom Drawer.
9 of 11 people
found this instruction helpful.
-
Kathleen from fall river, MA
- Really Easy
- Less than 15 mins
New part arrived, opened pkg. , Pulled drawer out. . . Snapped in new parts. . . . Done!! Saved myself $100. 00.
Was this helpful?
Thank you for voting!
f3 alarm
8 of 8 people
found this instruction helpful.
-
jeff from portage, MI
- Really Easy
- 15 - 30 mins
-
Screw drivers, Socket set
Removed screws. Unplugged temp sensor. Put screws back in. So easy a caveman could do it.
Was this helpful?
Thank you for voting!
Electric burner switch shorted out.
9 of 12 people
found this instruction helpful.
-
Armando G from Alice, TX
- Really Easy
- Less than 15 mins
-
Nutdriver, Pliers, Screw drivers
First I unpluggd the range and removed the back cover using a nut driver. Then I removed the knob by pulling (using a little force),Not very hard to do. I uscrewed two screws that hold the switch from the front of the range. Then I pulled the switch out about three inches and used pliers to disconnect the wires one at a time and connec
... Read more
t them to the new switch. finally I finished the installation by reversing all the steps. Total time to install the switch took approximately 5(five) minutes.
Read less
Was this helpful?
Thank you for voting!
Large burner wouldn't heat
15 of 31 people
found this instruction helpful.
-
Phyllis from Elberon, IA
- Really Easy
- Less than 15 mins
-
Nutdriver, Screw drivers
Removed back off of stove. Removed two screws that held in the switch, removed the wires that were connected to the switch and replaced the part.
Was this helpful?
Thank you for voting!
error sensor on display when oven was used
8 of 11 people
found this instruction helpful.
-
James from Clarence, NY
- Really Easy
- 15 - 30 mins
-
Screw drivers
I looked up the error code on line and found it was likely a faulty oven temp sensor. I was able to find the part and diagram at partselect.com and placed an order. The probe was in stock and arrived within a couple days. The repair took only about 20 minutes and works fine now. Thanks for your help partselect.com!
Jim
Jim
Was this helpful?
Thank you for voting!
Oven light bulb went dark; it needed replacing
10 of 17 people
found this instruction helpful.
-
Lise from CEDAR GROVE, NJ
- Very Easy
- Less than 15 mins
Twisted replacement bulb into place easily. Let there be light!
Was this helpful?
Thank you for voting!
2 elements stopped working.
9 of 14 people
found this instruction helpful.
-
Ruth from MORGANTOWN, WV
- Really Easy
- 30 - 60 mins
-
Nutdriver
My husband followed the video instructions and it was easy to fix.
Was this helpful?
Thank you for voting!
element stays on high
8 of 11 people
found this instruction helpful.
-
Billie from Arlington, WA
- Really Easy
- More than 2 hours
-
Screw drivers
found your website ,asked the question, got an answer, recieved a diagram and a possible problem diagnosis. obtained the part threw PartSelect quickly. took the knob off unscrewed two screws out ,disconnected the terminals and reconnected to new switch put the two screws back in and put the knob on!!! thanks ncountry "
Was this helpful?
Thank you for voting!
switch not always turn off
7 of 9 people
found this instruction helpful.
-
Jerrold from San Marcos, TX
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers
Took upper back off ( 6 screws), chech to be sure was right switch, pulled spade clip wires of, put on new switch, checked to see that it worked, replace cover.
Was this helpful?
Thank you for voting!