7909422940C Kenmore Range - Instructions

Disconnect power to Range at Electrical Service Panel control box. Remove 240 volt service electrical plug to range. Remove back top panel to expose element control switches. Remove element control switch to L.F. burner by first pulling off the control knob. You may need to use a large flat screw driver to pry behind knob to get it starte ... Read more d but it should come straight off. There are two screws revealed under knob that need to come off. Then the element control is easily, but carefully, removed out the back. Be careful you do not pull the "Hot Surface Indicator Light" switch off right above the element control switch. If you do, this will break the end off the plastic "Hot Surface Indicator Light" lens. If this happens you can still replace it but you will need to use super glue to make the "Hot Surface Indicator Light" switch stay connected to the clear lens. Install new element control in reverse order before gluing the "Hot Surface Indicator Light" switch as stated above or you will knock it off again. While holding the old element control in your hand with wires still attached, remove one wire at a time (making note of the location code for each wire) from old element control and install on new control. The new element control layout for the wire prongs will be different so you need to make sure you look for the code (like L1, H1, P) located on each prong location and put the same coded wire from old element control location onto new control prong code location. Reinstall new element control (with wires pushed fully onto prongs of new control) into panel with screws removed before. Reinstall knob, reinstall panel cover and reconnect range power plug. Restore power to Range at Electrical Service Panel control box With electric power restored, test element control by turning it on and see if it properly cycles on and off at different settings. If working properly you should be able to hear it click on and off and element heating and going off accordingly.

moved the range out to access back
removed 5 screws from back panel
removed 1 screw from thermostat installed new one
replaced screws, done in 20 minutes
problem solved

I just pulled the old ones out of the sockets, cleaned underneath, and replaced with new ones. No-brainer.

Husband very ill in bed. It's up to me!! Got a new bulb at HomeDepot and figured out how to get that wire 'thing' back in and the new glass cover installed. I DID IT!! WOW! My husband has always done these jobs around the house.......but now it's up to me.......and I'm not so dumb after all! I DID IT!! Now everyone who comes in ... Read more the house.....I show them what I DID!! :-)

I followed the video on the website. The probe is on back of the oven. Just unplug part and replace. That was not our fix all though as I later found that the igniter was not working. The igniter is also an easy fix but you access it through the front of the oven. Also an easy swap.

Oven is working great now.

Our iss ... Read more ues kind of fell between two of the descriptions so I went with high percentage cheaper fix first.

If your oven is intermittingly getting hot or to temperature of 100, it is probably the igniter.

Have used PartsSelect for Washing Machine, Dryer, Refridgerator and now the Range. Super easy to figure out needed parts and videos walk you through the repair.

Thanks

Went well, and working thank you ??

Just pulled the old cook top burner out and put the new one in .it took about 1 1/2 minutes

Used instruction video & replaced part.

The bulb has a plastic clear cover. That cover can just be carefully removed using a screwdriver. It's held in by a metal bracket. After you remove the cover. You'll just need to replace the bulb and then re-install the cover and bracket.

All you do it unplug the old one and plug in the new one.

I had open back cover and remove the switch than replace new switch. Makesure cable conection.

Very easy just had to pull the wire up that holds it secure.

I looked up the problem on YouTube and it said it was the oven temperature probe was going out. So I ordered the probe and it was shipped out, received within two days. Took out a few screws on the back of the stove installed it, put it all back together and it’s working perfect.

removed the screws holding the front part of the door and from there worked my way, untill the third glass.
It took a couple hours, my first time,. Overall easy,

Removed 4 screws on back cover removed 1 screw holding probe and unplugged the probe took it out and installed new probe.