- Home
- 79093852301
- Instructions
79093852301 Kenmore Range - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Oven Racks needed to be replaced.
11 of 14 people
found this instruction helpful.
-
Peter from Chicago, IL
- Really Easy
- Less than 15 mins
Slide out the old; slide in the new!
Was this helpful?
Thank you for voting!
Electric burner switch shorted out.
9 of 12 people
found this instruction helpful.
-
Armando G from Alice, TX
- Really Easy
- Less than 15 mins
-
Nutdriver, Pliers, Screw drivers
First I unpluggd the range and removed the back cover using a nut driver. Then I removed the knob by pulling (using a little force),Not very hard to do. I uscrewed two screws that hold the switch from the front of the range. Then I pulled the switch out about three inches and used pliers to disconnect the wires one at a time and connec
... Read more
t them to the new switch. finally I finished the installation by reversing all the steps. Total time to install the switch took approximately 5(five) minutes.
Read less
Was this helpful?
Thank you for voting!
Large burner wouldn't heat
15 of 31 people
found this instruction helpful.
-
Phyllis from Elberon, IA
- Really Easy
- Less than 15 mins
-
Nutdriver, Screw drivers
Removed back off of stove. Removed two screws that held in the switch, removed the wires that were connected to the switch and replaced the part.
Was this helpful?
Thank you for voting!
Error message on display ff30
7 of 8 people
found this instruction helpful.
-
Roger from CHICAGO, IL
- Really Easy
- Less than 15 mins
-
Pliers
Slid oven out removed one screw one plug replaced part took 5 minutes.told parts repair the error message and they sent me the correct part in two days will use them again saved me from Repair man wanted 85 dollars just to look at it my cost was 28 for probe and 8 dollars for shipping already helped neighbor with their stove they needed n
... Read more
ew ignighter 12 dollars repair place want 110 to come look at it this site walks you through repair best service!!!!
Read less
Was this helpful?
Thank you for voting!
Oven light bulb went dark; it needed replacing
10 of 17 people
found this instruction helpful.
-
Lise from CEDAR GROVE, NJ
- Very Easy
- Less than 15 mins
Twisted replacement bulb into place easily. Let there be light!
Was this helpful?
Thank you for voting!
element stays on high
8 of 11 people
found this instruction helpful.
-
Billie from Arlington, WA
- Really Easy
- More than 2 hours
-
Screw drivers
found your website ,asked the question, got an answer, recieved a diagram and a possible problem diagnosis. obtained the part threw PartSelect quickly. took the knob off unscrewed two screws out ,disconnected the terminals and reconnected to new switch put the two screws back in and put the knob on!!! thanks ncountry "
Was this helpful?
Thank you for voting!
switch not always turn off
7 of 9 people
found this instruction helpful.
-
Jerrold from San Marcos, TX
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers
Took upper back off ( 6 screws), chech to be sure was right switch, pulled spade clip wires of, put on new switch, checked to see that it worked, replace cover.
Was this helpful?
Thank you for voting!
Watch the video on line and it was really that easy to replaced the elements
6 of 6 people
found this instruction helpful.
-
Joseph from HATBORO, PA
- Very Easy
- Less than 15 mins
-
Screw drivers
Went very well and it works!
Was this helpful?
Thank you for voting!
Heating element broke
8 of 12 people
found this instruction helpful.
-
Joseph from Winter Park, FL
- Really Easy
- 15 - 30 mins
-
Socket set
Removed two screws in over pulled out part took off wires and put them on new elememt
Was this helpful?
Thank you for voting!
Oven wasn't heating properly for a few months and then stopped altogether
6 of 6 people
found this instruction helpful.
-
Matt from KENNETT SQ, PA
- Really Easy
- 15 - 30 mins
-
Socket set
The hardest part was pulling the oven away from the wall. Two bolts hold the sensor in place and a clip connects the electronics. Replacing the old one was trivial.
Was this helpful?
Thank you for voting!
Oven racks rusted
11 of 21 people
found this instruction helpful.
-
Wendell from Ocala, FL
- Really Easy
- Less than 15 mins
Ordered new racks and replaced them.
Was this helpful?
Thank you for voting!
broken lens over oven light
11 of 22 people
found this instruction helpful.
-
Leslie from Warsaw, VA
- Really Easy
- Less than 15 mins
Your service was OUTSTANDING...Ordered one afternoon, and before lunch time the next day, the delivery man rang my door bell...Thanks a bunch for you excellent service.....
Was this helpful?
Thank you for voting!
The elements were not heating up
6 of 8 people
found this instruction helpful.
-
Tanya from KALISPELL, MT
- Really Easy
- 15 - 30 mins
-
Screw drivers
It was really easy just unplugged it took off the back cover changed the part out put back cover on plugged it in and the elements were working great!
Was this helpful?
Thank you for voting!
switch had a diffirent lug configuration
9 of 18 people
found this instruction helpful.
-
Robert from Andrews, SC
- A Bit Difficult
- 15 - 30 mins
-
Screw drivers, Socket set
made a drawing as to where the wires were to placed on the new switch,took longer to do this than finding right tools. Important safety tip,always pull off the required breaker!!!
Was this helpful?
Thank you for voting!
Overlay was destroyed from use
5 of 6 people
found this instruction helpful.
-
Doug from Laramie, WY
- Really Easy
- Less than 15 mins
-
Screw drivers
Took back off the oven unscrewed the time control scaped old one off and put new one on. Than I put it back together again.
What a great place to shop!!!
What a great place to shop!!!
Was this helpful?
Thank you for voting!