79092302012 Kenmore Range - Instructions

I opened the door of the gas range and slid the rack in. No one can do this! I am amazing.

Disconnected power at breaker. Removed cooktop mounting screws, lifted top and propped in up position. Removed two screws and lowered two front burners mounting frame. Wiggled dual element free at the clips and proceeded to swap wires one at a time and realized the difference with connectors 1a and 2b much later when only the center portion was heating up. Finally figured out the problem and everything works as advertised. Pay attention if you own a Kenmore product.

Self easy

PS Great service Super FAST.
Thanks Jesse

Followed on-line instructions to remove the defective heating element. Some connection tabs on the replacement unit were different than the original. One tab was too wide to accept the stove's slip-on wire connector without fling down the tab width on the heating element. Thanks to some on-line instructions, wire connections to element 1a and 2a had to be reversed. If not for those instructions I would probably have ended up sending the unit back to the supplier, as an incorrect replacement !

My husband followed the video instructions and it was easy to fix.

Twisted replacement bulb into place easily. Let there be light!

Wife was cooking our thanks giving turkey, when an oder of burning was noticed. I walked over to the oven and smelled the area of oven light, it was bad. I turned off and unpluged oven. Got a screw driver, unscrewed 4 screws then noticed the burned switch from under the oven top. removed 3 wires, covered w/ elec. tape, and pulled oven light switch out front. looked at part number and ordered online. We were able to cook our turkey and enjoyed our meal.

Went very well and it works!

First unplug the stove before staring any of this task. loosen and remove three cross tip screws at the upper front of the stove top. You will need a piece of 1x3 wood about 1 1/2 feet long to hold the stove top up (sets at an angle upwards to the front). Loosen remove the bracket holding the burner you wish to replace. Disconnect the electrical wires connected to the burner. The burner is held in place with bracket clamps, remove the clamps from the oven bracket holding it. The burner will have a series if numbers in the back side, remove the brackets one at a time and reinstall on the same number on the new burner. do this to all 3 or four brackets. Install the new burner, install the bracket holding the burner, reconnect the wires. remove the wood brace and all tools. lay the stove top back down on the stove. plug the stove in and test the burner to make sure it works. turn off the burner and install the screws hold the stove to in place. Ta-Da your done. Also you tube has movie shots to give you a much better picture of what I just wrote about...

Your service was OUTSTANDING...Ordered one afternoon, and before lunch time the next day, the delivery man rang my door bell...Thanks a bunch for you excellent service.....

I replaced the bulb using my hands to twist the bulb in the socket located at the top of the refrigerator.

removed the old burner and put the new one in it's place.

The light apparatus was loose behind the panel. Remove the remaining part of the lens. Install the new lens from the outside of the panel and hold it in position, protruding into the inside of the panel. Slide the light apparatus onto the lens from the inside, allowing the bracket to hold it in place - it will be spring loaded, which will hold it in place.

I couldn't unscrew the leveling foot because it was rusted and corroded. The bracket holding it was easy to remove so I took the bracket with the corroded foot off and replaced it with the new foot and bracket. Very simple. I made sure I oiled it so it wouldn't rust again.

When the part arrived, I open the box. Cut off my breaker to the range. Pulled back the stove and unscrewed the back. Located the probe, unscrewed the one screw that held it in. I then unclamped the white connectors, remove the old probe, replaced it with the new one reclamped the connectors. Screwed it back into the range. Replaced the back and screwed that back together. It was so easy I was very proud of my self. I cut the breaker back on and cooked a can of biscuits just to see if it really worked. And it did. My bread was not burned, it was cooked to perfection.