Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
burner would not heat
killed the 50 amp power. removed 3 screws from above oven door slid out cook top, dropped brace holding 2 front burners. The connector corroded off had to look for a high heat connector to connect to the element, after that just screwed everything back together.
TURN BREAKER TO RANGE OFF! Move range out to access rear of the unit. Remove 6 screws to gain access to rear of controls panel. Pull knob off switch. Remove 2 pan head Phillips screws to take switch out. Lugs not in matching pattern but are clearly labled, swap wires one at a time. Reverse the disassembly steps and push the range back in place. DONE
i first replaced element after old smoked & quit. replaced switch but i noticed when i started to replace the wires one at a time something didn't seem right. after checking the #s on the old one, they didn't match up with the new one.luckily i had the stove diagram from a packet on the back of the stove. i traced each wire according to the diagram and everything worked out fine. i'm just glad i didn't replace each wire to wire.the #'s were on the switch where each wire went which was different than the org. even though they looked the same.
All of a sudden, one element in our glasstop range would not light and heat up. My wife and I were not sure what to do. Looked it up on the internet, found that you can do it yourself as others desribed the process of accessing the elements below. We decided to do that. It takes two people as one is holding up the glass because it opens like a car hood. While we diagnosed it was not a wiring issue (found a burnt wire, rewired the burnt wires (after mending the non burnt portions) to another element. The element that was not working before still did not turn on. Decided to purchase an element. While many online places sell elements, PartSelect actually allowed searching by brand with exploded views of the range to select the exact parts. This lessened the worry of purchasing a wrong element. When the part came (almost one day later), the repair was less than five minutes. Thank you PartSelect. I feel I saved a lot of money and aggravation.
oven would not heat up error code F10 showing on veiw screen
move the range out and unplug power supply, removing the back cover allows access to the probe, this can be done with screw driver or nut driver, loosen clamp that holds power cord in place and move backing out of the way, be careful sheet metal can be sharp, locate the probe unplug the connector and remove screw holding probe, pull old probe out install new probe, fasten down and plug in connector. attach backing and tighten clamp on power cord, plug in to power supply, turn on oven and give it several minutes for probe to work, it took only 20 minutes to replace the bad probe and the oven works like new hop this helps
I went all the way around the unit and removed screws holding top of unit in place. Removed knobs holding front panel in place. Remove control panel. top should come off. Remove screws attaching element top and metal frame. Undo bracket and remove element. Disconnect wires. Remember where they were attached. Replace element and reverse steps.
Disconnected power. Removed hold down fasteners for stove top. Fortunately, I did not flue down or use the double back tape to secure stovetop to counter. If this adhesive were used, it is possible I would have had great difficulty in removing range. I did not disconnect the wiring, but turned the range top over to access the cover. I removed the cover and easily removed the failed burner and installed the new ones. I had to pull 4 wires from the terminal strip and reattach them. The hold down strap for the burner was reinstalled. Range top turned back over and fastened down. Back in service.
First I unpluggd the range and removed the back cover using a nut driver. Then I removed the knob by pulling (using a little force),Not very hard to do. I uscrewed two screws that hold the switch from the front of the range. Then I pulled the switch out about three inches and used pliers to disconnect the wires one at a time and connect them to the new switch. finally I finished the installation by reversing all the steps. Total time to install the switch took approximately 5(five) minutes.
Both front burners began heating too fast and too high. One damaged the finish on the splash pan.
At the Frigidaire parts website, I found the parts and saw that there are videos that show how to replace the burner controls. In brief: 1) Slide the range/oven out so you can get to the back of the control hood. 2) There are three screws that hold the cover in place (the video showed four). 2a) The video also suggests using a #1 square bit. I found that there was indeed a square hole in the caps of the screws, but they also had a hex head that a 1/4" hex nut driver fits. So I used that. 2b) Be careful taking out the last (top center) screw. When it comes free, the cover can drop and bruise or cut your foot or the floor. Having a helper is worth it! 3) The switch for the larger elements has a red dot on front and back. Match it with the one in place that has a red dot. The switch for the small element doesn't have a dot. 3a) Holding a new switch in your hand, remove one wire at a time from the switch in the control hood and put it in the same place on the new switch. I found that for my stove, there was a fixture holding two wires and another holding three wires. This made it impossible to put the wires on wrong. 3b) When all wires have been transferred, pull off the control knob in front and unscrew the two screws that hold the old switch in place. Take out the old switch and replace it with the new switch. 3c) Use the two screws to attach the new switch in its place and replace the control knob. 4) Repeat for as many switches as you purchased. I did all four. 5) Replace the cover. 6) Slide the range back into place.
I found black deposits on all the switches, that must have come from a contactor inside, so I was glad I replaced them all.
Another tip: while the unit is out, clean off the sides and back that you couldn't get to while it was in place. For us, this took as long or longer than the steps above for replacing the switches.
