79091043400 Kenmore Range - Instructions

The old glides were broken off so I didn't know I needed these glides until I saw the parts section of the Manuel. When they arrived I snapped them in with no effort at all.
P.S. The shipping is fantastic here......i ordered on Monday received them on Tuesday. Now that's shipping:>)

The two back door glides were missing and broken (one of each), and needed to be replaced. Finding the parts online was MUCH easier than I expected,and the repair was remarkably simple. Parts snapped into place, the drawer had to be lined up, and it slid right into place. Very easy!

Turned off power, took back off stove removed old probe.
I had to splice wires since new probe ends did not match up.
the instructions were to splice the wires. I had the breaker off for about 3 hours. this is not in the instructions, but being a widow, I had to ask a few people why it would not come on after I connected the wir ... Read more es.
After waiting, I turned the breaker on and my range came back on.

Turned power off at electrical panel. Pulled oven away from wall. Removed back cover (6 screws), then unplugged wires from old receptacle. I had to pull the squeeze clips backwards & break them to remove the old receptacle - couldn't squeeze them enough to remove them otherwise. The old receptacle came out through the inside of the oven, ... Read more and the new one snapped in easily from inside the oven as well. Replaced wiring, installed new bulb, restored power & tested. Replaced back cover. Good time to vacuum under/behind where the oven usually lives before sliding it back to the wall.

Ever since we moved to this house I had used generic or standard drip pans found in any store. Needles to say they never fit properly so I always ended up with some burners tilting so my food would not cook evenly Until I decided to search for stove specific drip pans and this is how I bumped into your site. I am so happy now I can us ... Read more e all four burners at the same time if I wanted to, and my food cooks evenly since the burners are not tilting.

My husband removed the screws that held the top of the stove on and then lifted the top up. It is hinged. He then took out the old insulation, wiped down all visible parts of the interior with a bleach solution and replaced the blanket insulation with the new insulation. That took care of the problem!

was more of a job of splicing wires together than anything else. Loved the heat shrink electrical tubing
to put over the wires for insulation. used a hair
dryer. must buy more of that amazing stuff

pull out old burner, lifted range top change the terminal which took about 5 min. close top put new burner in and was ready to go. works great.

This should take approx 15-30 mins. It took me 1.5 hours as I pushed the terminals into the wrong end of the block. It's very difficult to get them out when you do that... However, there are no easy instructions on the block or in the instructions to tell you which end to push the terminals into!!! So, with a 50:50 chance of getting ... Read more it right, I got it wrong. I think most people would need to buy a new part if they do this. It would be very much easier if the block, had an arrow that simply said IN here so that this type of simple mistake is less easy to do... If you get that right, the fix is quite and straight forward. Good luck.

Removed the one remaining drawer guide and stared at it for 10 minutes trying to understand where it came from and how it worked. Looked it up on partselect.com. While there was no part number, the detailed photo on your web site was enought to assure me that you had the correct part. Ordered them in a few moments and three days later ... Read more I had the parts. The hardest part of the job was trying to understand how to install the widgets. After 20 minutes to crawling around in the stove's inards, I finally got the "aha" and the drawer on this antique stove was finished. Thanks! Couldn't have done it without you.

removed element , cut wires, conected wires,replaced element

I pulled out the old element and the new one just plugged right in.

I order the Element and received just in 4 days. It is Real incredible. I just opened the box and replaced the burners.

New part arrived, opened pkg. , Pulled drawer out. . . Snapped in new parts. . . . Done!! Saved myself $100. 00.

Just a replacement burner for my stove. No tools needed. Thank you for such a speedy delivery