This fuse, also known as a cartridge fuse, is a genuine OEM replacement part for microwaves. It has a glass cylindrical body with a metal cap on each end. The cap connects the fuse to the circuit. If the current goes above the fuse rating, the element inside the glass will melt and cut off the electrical current to the appliance. This pro...Read moretects the circuit and surrounding components from overheating and becoming damaged. Once the fuse is blown, the appliance will likely not operate at all, however, the fuse is designed to be easily replaceable. It is recommended to use insulated gloves and to avoid touching any exposed wiring connections. To replace the fuse, use a fuse puller to grip the metal caps and lift it out of the holder. Place the new fuse in the holder and ensure it is properly seated. Turn the appliance back on and check that the circuit is functioning.
This OEM waveguide cover in your microwave is a heat-resistant component that prevents food, grease, and moisture from entering the waveguide. It is typically located on the side or top wall of the cooking chamber. If the cover is broken, you may notice cracks, charring, or burns, and potentially see arcing or sparks during operation. Not...Read more replacing a damaged cover can lead to short circuits and the risk of electrical components touching your food. To remove the cover, start by disconnecting the microwave from its power source before opening its door. The waveguide cover is slotted or snapped into place, so gently slide or apply pressure to release it from the clips or slots. Please note that the cover is sold individually.
This door switch is designed for use with various makes and models of microwaves and is a genuine OEM part. This individually sold switch connects to the frame of the microwave through the door switch holder, which will need to be removed completely in order to replace this switch. If your microwave will not start, displays error codes, o...Read morer if the door will not shut properly and the inner light stays on, the switch could have broken from use and is in need of replacement. Due to the high voltage used within the components of microwaves, take extra caution when repairing your microwave. To replace the door switch in your microwave, disconnect the microwave from the power, and use a flat-head screwdriver to gain access to the switch through the main control panel.
This microwave door switch works with the door latch to control when the appliance can run, a worn switch may cause the microwave to lose power, fail to start, or trip a breaker, it fits select upper and lower switch locations, high voltage may remain inside the microwave after power is removed, use a trained technician for installation, confirm fit with the exact model number.
This adapter is a replacement connection component designed to join or transition between different system elements. It supports proper flow or connection stability and is commonly replaced when cracked, leaking, or damaged.
This lamp holder secures the interior light bulb in place while ensuring proper electrical contact for dependable illumination. Designed for durability and heat resistance, it restores safe and reliable lighting when the original holder becomes cracked, loose, or damaged.
This glass microwave turntable tray rotates inside the appliance to help ensure even heating and cooking. Made from durable, heat-resistant glass, it provides stable support for dishes during operation. Replacing a damaged or missing tray helps restore proper microwave performance and consistent results.
Ask our experts a question about this model and we'll get back to you as soon as possible!
We may have answered a similar question already! Search questions and answers left by others using simple keywords like "fit", "broken", "easy", or "quality" to find questions that match.
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Sort by:
Prev
1
2
Next
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Duane - For model number 79080353310
January 6, 2020
I want to remove the oven capacity light. The manual says remove 2 screws from the vent but there is only one on the right side and none on the left side of the vent. How do i get the vent off?
Hello Duane and thank you for writing.
Some models only have one screw, you should be able to take the screw out and then use a putty knife or similar to lift and slide. Sometimes debris is stuck and you might have to wash the lens down with some warm soapy water to get it loose. Do not forget to unplug your unit before attempting this. We hope this helps. Please contact us anytime if you require further assistance.
3 peoplefound this instruction helpful.
Was this helpful?
Thank you for voting!
Jennifer - For model number 79080353310
July 5, 2021
The microwave trips breaker every time the start pushed. Why would this happen?
Hello Jennifer, Thank you for the question. Normally this indicates the Door Switches are defective and will need to be replaced. We hope this helps!
Plate doesn't turn. Motor replaced but it only turns occasionally. Sometimes it turns 1/4 or 1/2 of a turn and stops. Could this have something to do with the plastic piece in the middle that the plate sets on top of?
Hello Rochelle, thank you for contacting us. Yes, the issue with the turntable not rotating properly could be related to the plastic piece, known as the turntable motor coupler, that the plate sits on. If the coupler is damaged, worn out, or not properly aligned, it may not engage with the motor correctly, causing the turntable to turn inconsistently or stop. The compatible turntable motor coupler for your model is part number PS1993374. We would recommend checking it to solve the problem. Glad to be of assistance!
Experienced intermittent beeping. Then it showed error code e-11 and stopping working. Any ideas?
Hello Chris, thank you for your question. That error code is in relation to a stuck keypad. We would recommend replacing the touch panel which is CONTROL ASSEMBLY Part #: PS8689517. I hope this helps!
Was this helpful?
Thank you for voting!
Prev
1
2
Next
✖
Ask a Question
Ask our experts a question on this model and we'll respond as soon as we can.
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Microwave tripped circuit breaker when turned on
40 of 67 peoplefound this instruction helpful.
Arthur from LUTZ, FL
Easy
15 - 30 mins
Screw drivers
Remove vent cover then remove touch screen control panel. When you remove control panel take photo of where everything is plugged in then unplug and remove control panel. 3 door switches located next to door in a plastic chassis. Test each switch with current tester. Remove the bad switch and replace with the new one. You tube DIY helped.
Was this helpful?
Thank you for voting!
Power would not come on, would trip breaker when connected.
18 of 28 peoplefound this instruction helpful.
JOSEPH from MIAMI, FL
Easy
15 - 30 mins
Screw drivers
First thing I dir was search YouTube for any related videos and found this one https://www.youtube.com/watch?v=uHj4H9Fdxrc, it was the exact problem my microwave was exhibiting. Once I verified the problem by troubleshooting, I removed the part and verified that the switches were working fine, the door latch assembly showed signs of wear
... Read morewhich was the cause of the problem. After receiving the replacement part I installed it, verified that power was restored to the unit and reassembled the microwave, works fine, hope it lasts a long time!
Read less
Was this helpful?
Thank you for voting!
Pressing the start, microwave will start and dies out. Electric is tripping.
11 of 18 peoplefound this instruction helpful.
ARNEL from WAUKEGAN, IL
Easy
15 - 30 mins
Screw drivers
The diagnosis is about an hour. Coz, I need to open the control panel, got a tester, and trsted all critical parts inside the panel. Also, replaced the fuse just to make sure its a new one. Found out it was a switch (bottom part) that control the open/close of the microwave door.
When found out the problem, the rest of t
... Read morehe work is easy.
My Orders
