79078530608 Kenmore Range - Instructions

Replaced the ingintion module, still did not work, replaced the burner complete with new ingiter , it now works but another one quit . the front right one has 5 ohms resistance ,replaced with new one with 0 ohms, the back left has 2 ohms resistance and now it does not work , will need to replace that burner allso. too bad you can't buy ju ... Read more st the spark module for the burner.

I was able to find the most common reason for my oven's symptom by searching online. I searched for the part I needed but was not confident that I would get the correct part until I looked on partselect.com. After verifying the part number with my owners manual and looking at the video on their website, I decided to order. PartSelect ship ... Read more ped the part as expected, and I was able to install it in less than 30 minutes. The only tool needed for installation was a nut driver. My oven is now working like new.

Many thanks to PartSelect for their comprehensive website and fine service.

Unplugged range; removed back cover; removed old oven probe. Installed new probe; replaced cover; connected power and turned on range - that simple. My only issue was probe was shipped in bubble rap and unit was slightly damaged (bent). Once straightened, the probe could be installed. Probe should have been shipped in sturdy cardboa ... Read more rd cylinder or box. I called customer service, they were very nice, and noted my feedback on my account in case the unit fails prematurely.

removed screws from back cover then pulled elect. plug apart. removed screw pulled out probe installed new probe put cover back on very easy only problem was that it said that 88% of time would fix the problem. will this time it didn't work oven still over heating.

Very easy to order,part was delivered promptly and installation was easy.I unscrewed a few screws and lifted the bottom panel out and put the new one in.

First thing. If your wife insists on helping buy 2
Because the first one will mysteriously come up broke. Just saying
This is a very easy replacement project. You can do it. TURN POWER OFF TO RANGE BEFORE REPLACING IGNITER Remove a couple screws take the heat shield out. Remove the bottom drawer unplug the igniter remove a cou ... Read more ple screws holding the igniter in place. Replace the igniter and screws. Plug in the igniter replace bottom drawer. Screw heat shield back down. Turn power to stove back on. You’re done

I pulled the oven away from the wall, unplugged the cord, removed the back panel then removed the screw from the old sensor.

When removing the screws that hold the igniter, the screws stripped. Not my first time so I very slowly removed the screws but they still stripped. I had to cut both with a small hacksaw but be careful not to damage the bracket that is welded to the burner. After successfully removing the screws had to go get 5/16 steel self tapping screw ... Read more s to install the new igniter. Use a self tapping screw to thread the hold first then remove and install the igniter with a new screw. Job was a success. Good luck with yours

Removed both oven racks the removed two screws in back. Lifted rear of panel until front lip of panel was free. Installed new panel in reverse order. I was recycled the old steel panel at our local recycling station.

Very simple. I removed the oven racks, loosened the two screws that held the old panel in place, lifted out the old panel and replaced it with the new one, then tightened the screws to hold the new panel in place. It took no more than 10 minutes.

Unscrewed old panel/removed and inserting new panel and used same 2 screws to secure in place.

Pulled oven away from cabinet area
Unplugged oven from wall outlet
Removed screws to free top panel from back of oven
Removed screws to free lower panel from back of oven
Probe backing was now exposed
Unplugged probe from connector
Removed one screw from probe housing
Twisted probe housing counterclock ... Read more wise then pulled probe out
Reversed the process to install probe
Plugged probe into connector
Reversed the panel removal process
Plugged oven back in to wall outlet
Turned on oven and tested with no further issue

Easy watched on line video

replaced it

Called fridgidaire and they told me the a F31 code means my temperature sensor is not working.
So I ordered one online. I installed it and I still have F31 code and still won't work. So what now? Do I trust them to tell me another part?