79075761000 Kenmore Range - Parts

This is a flat style oven igniter used to light the oven burner in a gas range. When the element in this igniter glows white hot, the gas is released from the safety valves, which lights the oven burner. If your range is not heating properly, or not heating at all, it might indicate a problem with this part. If the element in the igniter ...Read moreis only glowing red or orange, or not glowing at all, it will need to be replaced. This is a shorter style igniter. It is 3.72 inches in length, and it features an 18-inch wire lead. This kit includes the igniter, an instruction sheet, a mounting bracket, and the two ceramic wire nuts needed for installation. This part has an amperage range of 3.2 to 3.6. Unplug your appliance before you start any repair work.

This OEM 40 watt appliance light bulb is used for some ranges, refrigerators, freezers, and microwaves. Simply locate the existing bulb, unscrew it from its socket, and replace with new light bulb. If the existing bulb is broken in the socket, disconnect the power to the refrigerator and use a pair of needle nose pliers to grip the intern...Read moreal fragments of the bulb to unscrew. Replace with the new bulb and reconnect the power to the refrigerator. These bulbs are sold individually and are a commonly replaced part; consider ordering a spare.

This part is the replacement porcelain drip pan for your range or cooktop. It is a square-shaped drip pan and is black in color. It is approximately 9 inches in length and 9 inches in width. The drip pan will have one slightly rounded edge, and one flat edge, with a circular hole in the center that is approximately 2 1/8 inches in diamete...Read morer. The porcelain drip pan sits under the surface burner and catches spills. The main reason to replace the drip pan is if it is cracked or damaged. Be sure that your range is off, and the surface is cool to the touch before beginning this repair. This is an OEM part from the manufacturer.

Use this igniter with sealed burners.

The Frigidaire light bulb lens covers the interior light bulb in an oven. No tools are necessary to replace this item. After unplugging the appliance, slide off the wire bracket to remove the existing light bulb lens. Be sure to remove all broken glass, if applicable, before installing the new lens. It is recommended to check the state of...Read more the light bulb while the lens is off. This part is made of glass. The lens is a genuine Frigidaire part, sourced directly from the manufacturer, and is sold individually.

This part is the replacement inner oven door glass for your oven. It is made of glass and is approximately 16 inches wide and 7 inches long. The oven door glass allows you to see inside the oven when the door is closed. The main reason to replace the inner oven door glass is if the old glass is cracked, broken, or missing. This part is an OEM part sourced directly from the manufacturer.

This is now a new zinc and black-coated screw that will resist rust and seizing.

This is a red indicator light lens for an oven that covers the indicator light for the surface element. The indicator light signifies when the element is on and heated. This part is sold individually. It is recommended to check other red indicator lights in case they need to be replaced because they often wear at the same rate. It is diff...Read moreicult to see the light without the red lens. This part does not include the light. If your light does not illuminate, you may want to consider ordering the light as well. Tools required for this repair are a 1/4 inch nut driver and a stubby Phillips screwdriver.

Handle only.

Only available in Black.

Sold Individually. This white knob accepts a D-shaped shaft.

Also known as a temperature sensor. This part is used to detect the temperature within the oven cavity. **The following instructions only apply if the connector piece is different than the original.** Prior to cutting the leads, please check the length of the wire you will need. 1. Cut the leads on your original sensor and the replac...Read moreement sensor. Be sure to leave enough length to strip and splice the new probe and original connector together. 2. Strip the insulation, or wire cover, back approximately 1/4 inches on the new probe and original connector. 3. Twist the ends of your new probe and original connector together 4. Use a wire nut, or another high heat fastener to cover your exposed wires. 5. Install your new oven probe and re assembly your oven.