79071421401 Kenmore Range - Instructions

I took the brads that were left from the old gasket off with needle nose pliers. Then I put the new one on. It was very easy.

The range top had to be taken off along with the front panel to get access to the place the burner pipe connects. It took more time to unassemble and assemble the range than repacing the burner. The only issue was that the burner was sent without the bolts that will hold it in place so I had to go to local hardware store to get appropriat ... Read more e bolts.

Turn off gas,unplug,unbolt the burners(you have to do this to keep from bending and or kinking over the gas lines.Luck kept me from bending the lines out of whack.)All I needed was the electrode but I couldn’t find it available separately.I had to buy the whole front burner.Anyway remove the clip from the new part slide the electrode out. ... Read more Tilt the top of the range up take the clip off of the old electrode slide it out put the new one in install clip.Plug it in,rebolt all the burners in.Careful not to bend the gas lines.put the top down turn on the gas,plug it in and light.

Husband very ill in bed. It's up to me!! Got a new bulb at HomeDepot and figured out how to get that wire 'thing' back in and the new glass cover installed. I DID IT!! WOW! My husband has always done these jobs around the house.......but now it's up to me.......and I'm not so dumb after all! I DID IT!! Now everyone who comes in ... Read more the house.....I show them what I DID!! :-)

It went very well. Very quick. Just took out a couple of screws, took out the rest of the broken glass, slipped the new piece in and screwed it all back together. This was the first time I had ever tried to fix any part of a range/oven before, it was very simple...

turn the gas off unplugged it form electric removed the line took the flame plate off removed burner tube and the screw out with a nut driver that was all just put it back in reverse

I watched a YouTube video and followed their instructions. Pull the range out from the wall, unplug it. Take out a few screws with a nutdriver and take off the back. Unplug and unscrew the old control board. Remove the cover from the old control board (I had to use a razor knife to separate it from the control board). Stick it on the new ... Read more one (plenty of sticky stuff left), screw in the control board. Plug the wires back in, screw the back on, and you're in business. Easy, maybe five minutes work.

The bulb has a plastic clear cover. That cover can just be carefully removed using a screwdriver. It's held in by a metal bracket. After you remove the cover. You'll just need to replace the bulb and then re-install the cover and bracket.

It went easy, I ordered the part from another vendor, received it in 3 days and it only took about 20 minutes to install.
I do not recommend ordering from PartSelect!

Very easy just had to pull the wire up that holds it secure.

First I removed the oven door from the range by removing 2 screws from the door. Next I removed 2 more screws from the oven door to get to the panel beneath. Once the top portion of the door was removed there were 4 nuts holding the glass sections together. Once these nuts were out I removed the broken class, replaced it with the new g ... Read more lass and reassembled. It was a very easy and quick project. I was so happy to find the part. I thought I was going to have to buy a new range. Thanks.

After looking over the installation instructions I was confident that I could perform this on my own, However, changing the burner orifices was a bit tricky. Getting the original ones out worked well, they stayed in the nut driver when it was lifted. One of the new ones fell out when inserting it. Thankfully it fell all the way down a ... Read more nd I could retrieve it. A small piece of tape was needed to keep it in the driver. The rest of the install went per instructions.

Got a copy of the parts breakdown for the oven door from partselect. Com. Removed 8 screws from outer frame (3 top, 3 bottom, 1 on eah side). Removed the main glass pane from oven door, be careful when doing this as this is most of the weight of the door. It will want close on its own due to lack of weight. Removed the 2 top screw ... Read more s that attach the handle. Removed some screws from some plates that retain the 2 panes of glass of glass. Removed the third (most inner, broken) pane of glass. Replaced with new one. Reversed disassebly procedure for assembly.

There were only 2 screws that held the door handle & cap in place, removed screws & handle to get cap pieces off. Ordered new cap, - lost screws - cap delivered - no screws had to order screws, damn! They're expensive too !! Got screws, installed handle & cap, now wife is happy again!

Was easy...I pulled oven out from the wall so I could get to the back.i used a nut driver to remove small silver cover.matched up wires to the never module and re installed.pluged oven back in and burners lit perfectly