79071102004 Kenmore Range - Instructions

Disconnect power supply,reemove upper back panel,pop otut old switch,disconnect it ,connect new switch ,snap in place ,screw uppper back panel back in place,reconnect range power supply.

turn the gas off unplugged it form electric removed the line took the flame plate off removed burner tube and the screw out with a nut driver that was all just put it back in reverse

The bulb has a plastic clear cover. That cover can just be carefully removed using a screwdriver. It's held in by a metal bracket. After you remove the cover. You'll just need to replace the bulb and then re-install the cover and bracket.

I repaired with the use of 1 Phillips & 1 flathead screwdriver. It was very easy.

Got a copy of the parts breakdown for the oven door from partselect. Com. Removed 8 screws from outer frame (3 top, 3 bottom, 1 on eah side). Removed the main glass pane from oven door, be careful when doing this as this is most of the weight of the door. It will want close on its own due to lack of weight. Removed the 2 top screw ... Read more s that attach the handle. Removed some screws from some plates that retain the 2 panes of glass of glass. Removed the third (most inner, broken) pane of glass. Replaced with new one. Reversed disassebly procedure for assembly.

First I removed the oven door from the range by removing 2 screws from the door. Next I removed 2 more screws from the oven door to get to the panel beneath. Once the top portion of the door was removed there were 4 nuts holding the glass sections together. Once these nuts were out I removed the broken class, replaced it with the new g ... Read more lass and reassembled. It was a very easy and quick project. I was so happy to find the part. I thought I was going to have to buy a new range. Thanks.

Unpluged unit then using a flat screwdriver pride out old switch,pull off wires replace on new switch & push new switch in place. Repluged unit reset clock. Done!

Easy as pie. I had the new part in my hands in less than 48 hours. Fortunately for me it was a simple fix and I was literally cooking in under 15 minutes. I was a little worried about doing anything to a gas stove, but by looking at the other unbroken side, it was just a matter of snapping together a new assembly. What a wonderful web ... Read more site!

First, I read about the experiences of others who did this repair.

Then I removed the oven door by removing the single screw at each hinge - visible when the door is open - using a #2 Phillips screwdriver (the only tool needed for this repair). I placed the door on the kitchen table and removed the two screws at the inside t ... Read more op of the door - they also hold the handle onto the door.

I placed the four screws removed from the inside corners of the door -- into one corner of a tray I used to hold the parts in order. Then I removed the eight screws from the perimeter of the door and placed them into another corner of the holding tray. Then I turned the door over and removed the outside part of the door from the inside - as in removing the cover from a box.

Then I removed four screws holding the middle and outside glass panels and placed them in another corner of the parts tray. Then I removed two screws holding the steel panel against the glass. Then I removed the broken glass from the bottom of the tray. That's when I discovered I had ordered the wrong glass panel.

I called the PartSelect number to return the glass, and while discussing how to return the part, I asked if I had to call another number to get the correct part. The lady assured me she could process my order for the correct part. She was very knowledgable about the system and quickly found the correct part from the schematic. I received the replacement part 24 hours later and installed it within 20 minutes.

Overall a success story. Excellent service and easy work.

It was so easy. I am 66 yrs old. It only took 30 minutes and a screwdiver. I was totally amazed and I thank you.

I removed the oven door using a phillips screwdriver. It was very easy because I didn't have to worry about the door hinges springing the door back. I'm not really handy and it went very easy.

All visible screws on sides & top of door, including screws for the door handle have to be removed. Fairly uncomplicated job, but as the glass that needed to be replaced, was 4th of 4 layers of glass, all needed to be removed from the outside in, in sequence, to get to the broken piece. Then as long as everything was apart, cleaned all ... Read more pieces, before reassembling. Job much easier with two people, as one can hold & align all layers together, as the other tightens all the screws.

Followed your video and it was not hard at all

I used the tutorial as a guide, and went ahead with the repair. Because of the older model I was working on there were many more screws to remove, not a problem the repair was simple.

It was extremely easy, I took the two screws out by the hinges and then slid the door up off the hinges. After that I removed all the outer screws, a total of 8, and took the panel off. I then had to remove maybe 6 to 8 more screws in order to get to where the inside glass panel was. I then replaced the glass and put the door back togethe ... Read more r. It was such an easy job, that if anything else breaks rather than assuming I need to replace it Im gonna look on here to see if it can be repaired.