79070300702 Kenmore Range - Instructions

I removed the screws holding the door together,removed the broken panel and replaced it with the new glass
The part fit correctly and the re-assembly was easy.

All visible screws on sides & top of door, including screws for the door handle have to be removed. Fairly uncomplicated job, but as the glass that needed to be replaced, was 4th of 4 layers of glass, all needed to be removed from the outside in, in sequence, to get to the broken piece. Then as long as everything was apart, cleaned all ... Read more pieces, before reassembling. Job much easier with two people, as one can hold & align all layers together, as the other tightens all the screws.

Replaced uper orifice n adjusted oven as instructed.

Followed your video and it was not hard at all

The Appliance light was installed in a wood burning oven used by a commercial bakery. The entirely masonry oven is used to cook a specialty product with origins in Brazil.
We first drilled a 11-3/4 hole from the inside of the oven starting at the fire brick that passed through the concrete block outer shell of the oven to accommodat ... Read more e the insulated wiring to the on/off switch outside the oven. Then we commissioned a special steel cowling to enclose the the back and sides of the lamp so that the lamp faced down, instead of out and the back of the fixture was protected. The back of the lamp was attached to the insulated switch wires, then the custom lamp housing with filled with fire proof insulation. The entire lamp housing was then attached to the upper face of the masonry wall with 1/4" x 4" masonry bolt head screws. This type of installation was required because the oven overall size of 6' tall x 4' wide X 4' ID dimensions required a heat resistant light to illuminate 15 shelves of product being produced.
The oven lamp purchased works perfectly for the new oven. By the way, the oven does not have a brand, as it was created as a one of a kind, the brand of the oven lamp was taken from a Kenmore Gas Range.

I used the tutorial as a guide, and went ahead with the repair. Because of the older model I was working on there were many more screws to remove, not a problem the repair was simple.

I saw a chart of the oven door at site after I finally got the model number. I actually thought I had ordered the wrong part, third door in was last pane I thought, but actually this is inner most oven door, glass panel four. I had to find a correct screw diver which took awhile. I thought I didn't have the strength to turn the necess ... Read more ary screws, but easily could with correct screw driver. I followed other stories about removing handle, spring loaded door, so be careful it pops apart. A bit tricky to put back together, cause you have to hold door together against spring when you put cap on and door handle. Remove handle, remove top plastic cap. Will see screws holding glass and aluminum shield in place. Remove shield, need to remove screws holding glass two panes with holder. Shield pulls back and this glass just drops in. Reassemble door.

replaced it

Pull stove out to get behind it,unplug temperature probe plug. Remove temp probe from oven by removing the screw holding it in place on back of oven. Cut plug off temp probe unit leaving as much lead wire as possible on plug end. Strip wires on new probe and end of plug wires(one quarter inch). Then I used two small butt connectors to joi ... Read more n the stripped wires,one for each pair of wires. Two small wire 'nuts' may also be used as the connections are outside the oven and not exposed to the heat of the oven while it is in operation. Hope this helps the inexperienced 'do it yourselfers'--:)

The repair shop wanted 150 dollars to fix it. I ordered the glass and replaced it myself. It was really easy and all I need was a screwdriver. It took me about 30 minutes total.

First I removed the oven door screws, then I removed the outer handle and then there were 2 more sets of screws that actually held 2 panes of glass onto the door.

First I took the door off. Then I removed about a dozen screws. Than my wife insisited on cleaning the other two windows! Since the inside window was broken ;a lot of grease had gotten on the other two windows.She said she would never have another chance. After that I put everything back together. It took about an hour all together.

my dad and i did it together and it was easy. just had to remove the screws on the outside oven door pull the door apart, remove the old glass and put in the new and put the screws back in. hardest part was to get some of the screws out because they had been in so long.

It went okay but I had to have some help putting it back together. One person held the glass while the other person tightened the screws.

took screws on outer sides and then removed glass put in new glass replaced screws done