79064091301 Kenmore Range - Instructions

1. Removed two screws, pulled out the element, voltage tested the element and determined it was an open circuit (bad element).
2. Ordered the part from partselect.com
3. Disconnected element, connected the new one, and screwed it back in.

Shut off circuit breaker to stove and collected the tool from the basement. Turned on flashlight. Unscrewed the two hex nuts from the old element/back of the oven. Slid the old element prongs out of the back, exposing the connecting wires. Pulled the connecting wires off of the old element, carefully, so that the connections wouldn't come off of the wires. Threw the old element pieces in the garbage. Connected the new element to the connecting wires and re-fastened the hex nuts. My husband had wanted to call the repair man, but it didn't look too difficult, so I decided to try it on my own. Boy was he surprised when I fixed it, and for a fraction of the cost of hiring a repairman! Ladies, we can do this ourselves!!! :) Thank you for being there for us to order our part from, Parts Select, we had our new part in less than 24 hours, so the shipping was blazing fast!!! Keep up the good work!!! :)

removed screws pulled element out. removed wire from old element replaced with new element.very easy

My husband called our one and only parts store and got a price of $50 for the element. I used a search engine over the weekend and found the same thing for almost half the price. I received an email that said the element was shipped out on Monday, and it arrived on Tuesday afternoon! So my husband removed the two screws that hold the element in place, then replaced it with a new one. I am back in business for the holidays!

The element is attached to the back of the oven by two small screws. After unplugging the electricity to the oven and removing the attaching screws with a socket set (6.5 mm), you are able to pull the element several inches out from the back of the oven. Doing so exposes where the wiring is connected to the ends of the baking element. The element disconnects from the wiring with a light tug, after which the new element can be connected. I leave the "real" fix-it jobs to the pros ... this was a simple repair that anyone can do.

FIRST THING! UNPLUG THE OVEN! After I made sure there was no residual charge left in the oven I took a 1/4 inch socket wrench and attached to an interchangable screwdriver and crawled in the oven. I removed both screws and gently pulled on the element until the wire leads came thru. I then unplugged the leads and replaced the element with the new element and plugged them in. Then gently slipped the leads back into the oven and replaced the screws. Turned on the oven and WHA LA!! We had our oven back and running and had chocolate chips cookies in a flash! It was fast and easy and saved me a fortune!

The old glides were broken off so I didn't know I needed these glides until I saw the parts section of the Manuel. When they arrived I snapped them in with no effort at all.
P.S. The shipping is fantastic here......i ordered on Monday received them on Tuesday. Now that's shipping:>)

PF alarm appeared on display. Noticed clicking when cord was moved. Had arced for some time and melted original block. New part slightly different. Only has 3 lugs, old one had six. Stack using washers provided. Take note of colors before disassembly. Use caution while working through access opening. The edges are sharp. Only tools needed are phillips screwdriver, deep socket for lug nuts. Nut driver optional. Hope this is helpful.

The two back door glides were missing and broken (one of each), and needed to be replaced. Finding the parts online was MUCH easier than I expected,and the repair was remarkably simple. Parts snapped into place, the drawer had to be lined up, and it slid right into place. Very easy!

First thing I did was to turn off the range supply breaker. There were two screws, one on each side, that held the lower element into place. I used a phillips head screw driver to remove the screws and pulled the element out for access to the wires. I pulled the connectors off of the element and remove it from the oven. I them put the new element into place, attached the wires, replaced the screws and turned on the breaker. It was an easy fix.

Turned power off at electrical panel. Pulled oven away from wall. Removed back cover (6 screws), then unplugged wires from old receptacle. I had to pull the squeeze clips backwards & break them to remove the old receptacle - couldn't squeeze them enough to remove them otherwise. The old receptacle came out through the inside of the oven, and the new one snapped in easily from inside the oven as well. Replaced wiring, installed new bulb, restored power & tested. Replaced back cover. Good time to vacuum under/behind where the oven usually lives before sliding it back to the wall.

Most of the job is simple fastener mechanics.
Use a nut driver or Phillips screwdriver. Remove rear panel.

Pull out control knob. If it is stuck, wrap a small rag around the back of it and pull the rag steadily.

Carefully match marked terminals on the replacement switch with those on original. Switch terminals may not be in the same location. Replace wires one for one, one at a time.

Carefully select the correct knob filler for the switch post. Several are supplied. Proceed with logic and measure the shaft length and the filler length and type to match.

Ever since we moved to this house I had used generic or standard drip pans found in any store. Needles to say they never fit properly so I always ended up with some burners tilting so my food would not cook evenly Until I decided to search for stove specific drip pans and this is how I bumped into your site. I am so happy now I can use all four burners at the same time if I wanted to, and my food cooks evenly since the burners are not tilting.

I removed the two element screws, one on each side. This was very easy and fast.
I then pulled the old element towards me about
three inches to expose the wires attached to each
end. The wires have a slide on terminal connector
so replacement is easy, but you must hold the
terminal connected to the wire then pull the element off. Do not try to pull off the element by pulling on the wire you can cause damage to the
wire and create a new problem. Once the old element was removed I attached the wires to the new element by sliding the terminal connectors on each end and pushed them firmly into place. I then pushed the new element back and replaced the screws on each side and the repair was complete.The repair took all of about 5 min. The best part was I received the the new element from Parts Express the next day and had the oven working within 24 hrs.. The repair service could not do it that fast. Do it yourself, you can save a lot of money!!

First I unplugged the the stove. I then unscrewed the two screw holding the element. Because I had read the other repair reports on the site, I was very careful in pulling the element out so I wouldn't lose the wires in the rear of the stove.
Once out, I held them with the pliers and gently pulled the element until it was loose. Plugged in the new element screwed it back in and plugged in the oven. Worked like a charm. By the way the part arrived the day after ordering it!!!! This is a great site.