79060071793 Kenmore Range - Instructions

PF alarm appeared on display. Noticed clicking when cord was moved. Had arced for some time and melted original block. New part slightly different. Only has 3 lugs, old one had six. Stack using washers provided. Take note of colors before disassembly. Use caution while working through access opening. The edges are sharp. Only tools neede ... Read more d are phillips screwdriver, deep socket for lug nuts. Nut driver optional. Hope this is helpful.

Most of the job is simple fastener mechanics.
Use a nut driver or Phillips screwdriver. Remove rear panel.

Pull out control knob. If it is stuck, wrap a small rag around the back of it and pull the rag steadily.

Carefully match marked terminals on the replacement switch with those on original. Switch terminals ... Read more may not be in the same location. Replace wires one for one, one at a time.

Carefully select the correct knob filler for the switch post. Several are supplied. Proceed with logic and measure the shaft length and the filler length and type to match.

Ever since we moved to this house I had used generic or standard drip pans found in any store. Needles to say they never fit properly so I always ended up with some burners tilting so my food would not cook evenly Until I decided to search for stove specific drip pans and this is how I bumped into your site. I am so happy now I can us ... Read more e all four burners at the same time if I wanted to, and my food cooks evenly since the burners are not tilting.

I was selling my home and did not realize that the anti-tip bracket was not originally installed. A home inspection caught the problem and the buyers required that I install one. I could not find the original and obviously the installer never put it in place to begin with. The buyers wanted this resolved within a week so I had to act f ... Read more ast. I could not find one locally so I found what I needed on your website. It arrived in a couple of days and was easy to install. I used the template provided in the kit and drove the screws through the bracket into the wood plate behind the drywall. Pushed the range back in place and that's it. Couldn't get any easier.

My husband removed the screws that held the top of the stove on and then lifted the top up. It is hinged. He then took out the old insulation, wiped down all visible parts of the interior with a bleach solution and replaced the blanket insulation with the new insulation. That took care of the problem!

Remove old element by removing two screws on back wall of oven, pull attached wires out about 6" and disconnect. Reverse to install, very easy. Of course the oven door makes it harder to get at things, but it all worked out. Partselect was the only place I could find the element since the stove is 18 years old. I love keeping appliances g ... Read more oing as long as possible.

First of all I removed the top panel then removed the switch. I then took pictures of the switch & drew a sketch with all the info. Then I went to your web site, matched up the switch & ordered.
When the switch arrived I went thru the above replacing the bad switch.

Lifted the oven top, removed the controls cover, slipped the lens into the hole and slid the light holder device onto the lens

order pcs fit perfect.

First I unplugged the stove, and removed the upper-back panel. Then I pulled off the control knob. Then I removed the two screws holding the switch to the stove. Then one-by-one I removed the wires from the old switch and connected them to the corresponding tabs on the new switch. Then, using the knob adapter supplied with the new swi ... Read more tch, I figured out how much of the knob shaft I had to remove from the new switch to position the knob the correct distance from the face of the stove. Then I tested the switch with a voltmeter as instructed, and then I hooked up the last wire.
Partselect.com is an awsome website!!! I was able to review comments form other do-it-yourselfers that had similar problems. Then I looked up the Partselect schematic drawings of my stove and was easily able to find and order the part I needed. The part arrived at my house within a couple of days and I had the stove fixed in no time.

Very important first step: Turn off the circuit breaker for the range or disconnect the power cord.
I removed the oven door to make it easier to access the back of the oven; remove two screws and the door lifts off of the brackets. Removed a screw from the top of the oven that secures one end of a wire that supports the broil eleme ... Read more nt. Removed two screws that secure the broil element plate to the back of the oven. Pulled the element forward exposing the end terminals and wires. The wires are connected to the element by spade connectors. Used long nosed pliers to remove the connectors from the element. Pushed the connectors on to the new element and stuffed the ends of the element and wires back through the opening and the insulation. Reinstalled the two screws holding the element in place and the screw holding the wire in place across the top of the oven. Reinstalled the door. Took less than 30 minutes.

Slide out the old; slide in the new!

I pulled out the old element and the new one just plugged right in.

I order the Element and received just in 4 days. It is Real incredible. I just opened the box and replaced the burners.

Just a replacement burner for my stove. No tools needed. Thank you for such a speedy delivery