79045069400 Kenmore Range - Instructions

The repair was simple; first I removed the 2 screws from the old element and disconnected the wires and then I inserted the new element reconnected the wires and replaced the screws . The repair was easy and took less that 15 min. The oven works as good as new and I saved alot of money by doing it myself.

Replaced clock control by removing surface burner control knobs and plastic nuts, and then the cover over the oven control. Two screw hold the clock in place, after removal and disconnecting the plug-in you can reinstall the new clock control. The Heat Sensor inside the oven will also need to be replaced. It is located inside the oven ... Read more and attached with two screws; the back of the oven will need to be removed to unplug. Reverse removal procedure and turn the power back on to the stove.

PF alarm appeared on display. Noticed clicking when cord was moved. Had arced for some time and melted original block. New part slightly different. Only has 3 lugs, old one had six. Stack using washers provided. Take note of colors before disassembly. Use caution while working through access opening. The edges are sharp. Only tools neede ... Read more d are phillips screwdriver, deep socket for lug nuts. Nut driver optional. Hope this is helpful.

I pulled my unit out of the wall and noticed that the insulation around the top broiler element was a bit brown. Closer inspection revealed that the element had shorted somehow to the oven itself and caused the element to become non-functional. I tried measuring the resistance first, and it was within typical values for the other elemen ... Read more ts, but I decided to replace the element anyway.

I ordered from PD and the part arrived just a few days letter by regular shipping. I undid the screws holding in the element, undid the wire connectors and replaced the broken element with the new one. The element worked like a charm and I was back in business for cooking.

I followed the directions by clipping wires to old burner socket, splicing the wires to new terminal block, screwing down new "block bracket," and plugging in new burner.

PartsSelect serivce was AMAZING - I ordered online on Sunday afternoon, and the part arrived Tuesday with standard shipping! First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires from the old element, then replaced with new. WARNING - you MUST kill the ... Read more breaker, because the element is "hot" even when it's off.

Turned power off at electrical panel. Pulled oven away from wall. Removed back cover (6 screws), then unplugged wires from old receptacle. I had to pull the squeeze clips backwards & break them to remove the old receptacle - couldn't squeeze them enough to remove them otherwise. The old receptacle came out through the inside of the oven, ... Read more and the new one snapped in easily from inside the oven as well. Replaced wiring, installed new bulb, restored power & tested. Replaced back cover. Good time to vacuum under/behind where the oven usually lives before sliding it back to the wall.

Very easy---simply unplug the burners, remove the old pans and replace with the new ones

I was extremely pleased with the easy ordering and prompt delivery of parts that actually fit as they should!

When we bought our home less than a year ago, we had three functional burners on our 40" wide 50's classic Kelvinator (not close to standard size these-a-days). After a few months of use, two more burners went out for good and we were stuck using the back left burner for all of our cooking. I opted for the premium burners and made sure to ... Read more compare my terminals with the ones online to be sure they mounted the same. I removed the burners and terminals, clipped the wires going into the terminals, and removed the top of the stove. I followed the directions that came with the new terminals, pushed in the new burners and viola! All four burners now work. I gave the stove a general cleaning and now my 1954 Kelvinator looks and cooks like it is brand new. It was easily the best $109 I've spent on my home.

I removed the two screws and then used pliers to pry apart the wiring. I unplugged the connectors and removed the element. The new unit arrived in three days and I plugged it in, replaced the screws and turned the oven on and made a pie! Very Satisfying and easier then I ever thought it would be. We figured we saved $200.00. The service p ... Read more lace where we live charges $125.00 to come out and assess and then parts and service on top of that.

was more of a job of splicing wires together than anything else. Loved the heat shrink electrical tubing
to put over the wires for insulation. used a hair
dryer. must buy more of that amazing stuff

Took out the bad element and replaced it with the new element in less than 5 minutes. Simple Stuff with the right part. Thanks Parts Select!

I simply removed the old drip pans and inserted the new ones which matched and fit perfectly.
I'm glad I found you on line. Your service was fast and the whole transaction was easy!! Thanks.

This should take approx 15-30 mins. It took me 1.5 hours as I pushed the terminals into the wrong end of the block. It's very difficult to get them out when you do that... However, there are no easy instructions on the block or in the instructions to tell you which end to push the terminals into!!! So, with a 50:50 chance of getting ... Read more it right, I got it wrong. I think most people would need to buy a new part if they do this. It would be very much easier if the block, had an arrow that simply said IN here so that this type of simple mistake is less easy to do... If you get that right, the fix is quite and straight forward. Good luck.

Easier than painting my toenails!! The gasket came out easily just by pulling with my hands. Replacing it with the new one was even simpler. The clips are already attached to the gasket and easily slip into the holes on the door. I used the end of a tupperware orange peeler to push the unfinished ends of the gasket into a slot at th ... Read more e bottom and that was it! A new, perfect seal and it looks and works great!