7900 (248701) Graco Sprayer - Parts

This part is available as an individual replacement. The cap attaches to the frame and is made out of plastic. A hammer may be necessary during the installation of this item. Over time this part may break and will need to be replaced. This item is an OEM from Graco for use in sprayers.

The O-Ring is a blue, rubber ring which is used to provide an airtight seal between connected parts, such as between the diffusion tube and filter cap. If the part is broken due to general wear/fatigue, there will be a leak and it should be replaced. Refer to your make, model and diagrams to ensure this is the best part for you.

This is a genuine OEM sourced part which is specially designed for use with Graco sprayers. It is an identical replacement for a missing or a faulty threaded deflector that was included with a new unit, please make sure to refer to the owners manual and the appropriate diagrams of your model for the correct location and application of thi...Read mores component. Keep in mind this high-quality item is made of durable material and is sold individually.

This OEM wheel is constructed of plastic and rubber, and comes in black/white. It attaches onto the axle shaft to provide easy movement. Installation is rated as "Easy" by customers and will require a socket (Tip: Make sure tire is inflated to proper PSI). If the wheel is flat or damaged, then it may be broken and require replacement. Refer to your make, model and diagram to ensure this is the correct part for you.

This Tool Box is manufacturer-certified, blue, and constructed of metal. It's rated as being "Easy" to use, and requires a screw driver and wrench set. It can be used to store and protect the components of the airless pain sprayer. It attaches to the frame of the unit. If broken or damaged, it should be replaced. Refer to your make, model and diagrams to check if this part is right for you.

This is the return hose assembly, or return line, which is designed for various models of airless paint sprayers and is sold as an individual part. The return line is designed to allow paint and pressure to be returned into the reservoir, and simultaneously connected to a specific port on the sprayer for a continuous paint cycle. This ret...Read moreurn line is comprised of a high-quality rubber and metal pump attachment at one end and a metal tube and plastic reservoir attachment at the other end. Depending on your model, you may need a set of pliers or a wrench to disconnect and remove the old line. Before you replace your old line, it is recommended that you wrap the metal end of the line with Teflon tape to create the best seal possible. When replacing the line, disconnect the sprayer from power and release any pressure in the spray gun by squeezing it until no more pressure is felt.

This 3/8-inch male pipe plug is used to seal unused ports in fluid transfer systems and manifold housings on high-pressure spray equipment. Made from durable steel, it helps maintain system pressure and prevent leaks during operation. It’s a simple, direct replacement for damaged or missing plugs to restore proper sealing and reliable performance.

The Manifold Filter Support (Tube, Diffusion) is a black, plastic part which is used to secure the filter. It attaches with the filter mesh and the filter cap. If broken, damaged, or worn it should be replaced. Installation is rated as "Easy" by customers. Refer to your make, model and diagram to ensure this is the correct part for you.

The OEM Gasket is a grey foam part used to provide a seal between two joining pieces. If broken, there will be a leak and the part should be replaced. Refer to your make, model and diagram to check if this is the correct part for you.

The Filter Cap is a silver, metal cap which is rated as "Easy" to install. It attaches on the diffusion tube and mesh filter, in order to prevent debris from entering. If broken it will clog, causing spray issues. If broken, damaged or worn out it should be replaced. Refer to your make, model and diagram to ensure this part is right for you.

This is a label used to display the functionality of various electric airless paint sprayers. This label reads: Pro Connect, which is a function within the spray gun of the compatible sprayers. This label measures approximately 4-inches long and 1-inch wide and is a genuine OEM label that can directly replace the label on your machine if ...Read moreit is missing or damaged. This label is meant to be displayed on the drive cover of the paint sprayer and can be replaced easily with no tools at all. To replace this label, remove the old label (if applicable), and clean the area on the drive cover of your sprayer to remove any residue. Install the new label with evenly distributed pressure, to ensure adequate and even adherence.