7898XRW Magic Chef Microwave Oven Combo - Instructions

****Threw the breaker switch for the oven to the 'off' position****. Opened the oven. Unscrewed the phillips head screws at the back of the old element. Removed the connecting wire, taping them to the stove so that they wouldn't recede into the hole. Securely attached the connecting wires to the new element. Pushed the wires back into th ... Read more e holes in the stove. Removed the tape from the oven. Screwed the element into place. ****Threw the breaker switch back to the 'on' position****. Process took under 10 minutes.

DO NOT FORGET TO UNPLUG OR TURN OFF BREAKER BEFORE DOING ANYTHING WITH THE WIRES. Don't forget to turn it back on again when you are done.

pulled breaker,removed oven door,removed 2 screws,pulled bake element out 3 inches,pulled connections off,pushed connectors on new element,pushed new element back and replaced screws,replaced oven door ,pushed breaker back and turned on oven and let it heat up to 350 degrees.
Total time 10 minutes,even a caveman could do it.

Turn Off the BREAKER!!!
Unplug the stove/oven
Opened the oven door
Unscrewed the baking element for the oven
Pulled the old element out about 3"
Disconnected the wire clip on both sides
Plugged the element into the clips
Screwed element back into place
Plugged oven in ,turned on breaker
PREST ... Read more O DONE

I removed the two mounting screws and pulled the harness through the opening unsnapped the sensor from the harness and installed the new sensor i didn't have to used the adapters the new sensor fitted

I had the problem before and had to call in a Tech to repair the baking element in my oven. It cost me $150.00 for the repair. This time I decided to do the repair myself, so I went online and found this site The instruction video made it very easy. I am very proud of what I was able to do without calling a Tech. My oven works like new, I ... Read more t only cost less than $40.00 for the total repair. I am so glad this site were there when I needed them.. Thanks a Lot..

Extremely simple repair to make. Move stove away from wall and disconnect power. Remove the oven racks. Remove the rear sheet metal panel covering the wiring harnesses. Caution: Sharp edges and corners on sheet metal.Sensor is located in upper left corner on rear oven wall. Using a long-shafted #2 Philips screwdriver, remove the two Phili ... Read more ps head screws and gently pull the sensor 1" away from the oven wall. At this point, it will help to have an assist from someone while you are behind the range. Have the assistant gently tug on the sensor while you watch for wires moving on the rear of the range. After locating the sensor wires, gently disconnect the plastic connector clip. Note: plastic connectors become brittle with age and exposure to heat Move to front of range and gently remove sensor from rear wall by pulling the wiring through the oven wall. Before inserting the new sensor wire through the oven wall, "dry fit" the wiring connectors to see that the new sensor is a correct connection. Make connection, and secure the sensor to the rear oven wall with the two screws. Install racks, reinstall rear sheet metal panel, and connect the power. Set the oven baking temperature to a moderately low temp, 300 - 350 deg. to test the new sensor.

Removed 2 screws, disconnected wires, attached wires to new element, put screws back. Turned oven on. Perfect.

Removed the failed bake element per the video linked in the Partselect email. Unlike the video on YouTube the PartSelect video shows that the bake element can easily be replaced through the oven door and it is not necessary to slide the range out and remove a rear panel.

First I removed the two screws that hold the element in place. I then pulled the element out aobut 3 inches and disconnected the wires.

I unplug the stove first. Then took off two screws that held the bake element in place. Pulled off the connectors using the pliers. Had to use pliers because they were really snug. Plug in the wires to the new base element. Crimped down the connectors a little bit to make sure they were snug. Inserted the bake element back into the ... Read more holes at the back of the oven. Put the two screws back in. Plugged the oven back in and turned it on to make sure it worked. Lastly, tossed the old bake element in the trash. Really easy job. Glad I didn't pay anybody to do this.

Removed 2 phillips screws, unplugged 2 wires, threw away old element. Installation of the new element was just as easy but in reverse order. Piece of cake!

Took two screws out unplugged the element and plugged the new one in and replaced the screws and turned the breaker back on. Works great...Piece of cake..jk

installed part,turned unit on-temp still cold. reset digital control, up 35 degrees, still cold. un-plugged unit,re-connect after 10 min. still cold.

Removed the electrical power. Lifted up the top. Slipped off the two connecting wires. Removed two screws. reinstalled new thermostat in reverse order.

Turned off power, removed 2 screws, un-hooked the connections, them put in the new element in reverse order.