74569 Toro Lawn Mower - Parts

This solenoid is an authentic manufacturer replacement part for use in lawn tractors. It sends the electrical current from the battery to the motor to allow the tractor to start and run. The solenoid will need to be replaced if it is damaged or experiencing electrical failure. Signs of a failed solenoid include difficulties cranking the e...Read morengine, hearing clicking or no sound at all when turning the ignition key, and a starter that cannot stop running. Begin the repair by disconnecting the battery for your safety. Take a note/picture of how the wire connectors are routed before disconnecting them. Remove the bolts that secure the solenoid in place and pull the faulty part out. Position the new solenoid in its place and secure it with the mounting bolts. Use your notes to reconnect the wiring and battery.

This O-ring, also known as a round seal, is an authentic OEM part used in lawn and garden equipment. It is a small, circular, rubber ring that helps create an airtight seal between the oil filter filler and engine to prevent leaking and ensure adequate lubrication. It is common for the O-ring to become brittle and lose its elasticity due ...Read moreto aging, and exposure to chemicals and high temperatures in the equipment. If an O-ring fails, it can result in oil leakage, leading to reduced equipment performance, and potential damage to the surrounding components. Carefully the oil ring off the sealing surface and clean the area thoroughly to ensure a proper seal for the new O-ring. Lightly lubricate the new O-ring and press it on to the sealing surface.

This is an Authentic Manufacturer Sourced replacement part used on Kawasaki Engines. This rocker cover gasket is for the cylinder head. It is sold Individually. It provides a strong seal to protect from leaks. Over time gaskets tend to deteriorate and would need to be replaced. You would need a Wrench to replace this item.

This head gasket is an original manufacturer replacement part for power equipment. It is a seal that sits in the area between the cylinder head and engine block. It is responsible for preventing air and fuel from escaping during the combustion process, which allows the engine to run. Over time it is normal for the gasket to wear down due ...Read moreto friction, exposure to heat and aging. However, if the gasket is not properly installed it may fail prematurely. If you notice that your engine is overheating, misfiring, releasing white smoke and your equipment has low power, the head gasket likely needs to be replaced. To access the faulty gasket, you will need to first remove the cylinder head. Carefully lift the gasket off and clean the mating surfaces to remove dirt, debris, and residue. Position the new gasket on the engine block and secure it with the appropriate fasteners.

This is an genuine OEM replacement part used on Kawasaki engines. The push rod rides on the camshaft to push the exhaust valve open during the exhaust stroke. A bent pushrod can not only affect your engine's performance, it can seriously damage other parts if the problem is not taken care of immediately. This part is made out of metal and it is sold individually.

It is a genuine OEM item that is made for Toro lawn and garden equipment. This is a special component which helps to provide a tight fit between connected parts. Unfortunately, over time it may wear out, get damaged or lost eventually requiring a replacement. This high-quality bushing is made of durable material and is sold as an individu...Read moreal item. To ensure the proper repair procedure, check the parts diagrams for your specific model.

This genuine Kawasaki fuel pump is an OEM-sourced replacement part designed to ensure reliable performance and quality. It is intended for use with small engines and plays a vital role in circulating fuel through the system by responding to pressure changes within the engine. Built for durability and consistent operation, this fuel pump i...Read mores sold individually and is ideal for restoring proper fuel flow in compatible engine models.

This is a genuine OEM sourced hardware that is specifically made for use with Toro lawn and garden equipment. It is a standard hardware which may have multiple applications depending on the model of your unit. Please make sure to refer to the appropriate diagrams for the correct location and application of this part. Keep in mind this hig...Read moreh-quality flange nut is made of durable metal and is sold individually. Note, you will need a wrench to secure or remove it.

This gasket is supplied by the original equipment manufacturer for use with Kawasaki engines commonly installed on a variety of lawn and garden equipment. It helps to distribute the pressure evenly and provide a tight seal for the manifold. Over time it may wear out and begin to crack eventually requiring a replacement. For the exact loca...Read moretion and the correct application, please refer to the appropriate diagrams of your model. This high-quality gasket-manifold is made of durable composite material and is sold as an individual component. You will need a wrench set to remove and reattach the manifold when performing this repair.

This fuel return hose is a genuine OEM replacement used on small gasoline engines to route excess fuel back to the tank, typically as part of the carburetor purge system. Made from flexible, durable material, it helps ensure proper fuel circulation and smooth engine operation and is an ideal replacement when the original hose is cracked, hardened, or leaking, which can cause starting issues or poor running.