74409 - Parts

This is a genuine Toro replacement part that has been sourced from the original manufacturer to be used with snowthrowers. The metal flat washer is used to disperse pressure put on a part assembly by a nut or bolt across a wider surface area. This item is used with several different models of snowthrowers. It is recommended to review your...Read more model\\\'s part diagram to confirm the washer\\\'s compatibility and usage. The flat washer is priced individually.

A genuine item that is supplied directly from the original equipment manufacturer for use with Kawasaki engines commonly installed on lawn and garden equipment. It is a special screw for the armature, make sure to refer to the appropriate diagrams of your model for the correct location and application of this hardware. Keep in mind this high-quality hex socket screw is sold individually.

This is a genuine OEM sourced spacer which is specially designed for use with Toro snowthrowers. It is an identical replacement for a missing or damaged spacer that was originally installed on a new unit, please make sure to refer to the appropriate diagrams of your model for the correct location and application of this hardware. Keep in ...Read moremind this high-quality component is made of durable metal and is sold individually.

This is a genuine Toro replacement part. The friction washer is designed by the manufacturer for use in lawn tractors. This part is used to help secure the idler arm and apply friction to its motion. You will require a wrench when replacing this item. This part is sold individually.

This is available as an individual replacement part. The o-ring seal goes next to the charge pump cover and is made of rubber. During replacement, it may require a socket set to help install this item correctly. It will need to be replaced if it becomes broken. It is a genuine OEM sourced part which is specially designed for use with Toro lawn tractors.

The stud goes between the hex nut and the engine shroud. This is a genuine replacement part sourced from the original manufacturer for use with engines made by Kawasaki and Toro. It is made of metal and is available as an individual replacement part. A wrench may be necessary during the installation of this item. This part may become bent or broken and will need to be replaced.

It is an authentic OEM part that is specially made for use with Toro and Lawn Boy snowthrowers. This is an identical replacement for a faulty or a missing hardware that was installed on a new unit. It is one of the screws utilized to secure the upper and the lower handles. This high-quality component is made of durable metal and is sold a...Read mores an individual item. Make sure to refer to the appropriate diagrams for your model to ensure the exact location and the correct application. A wrench will be needed to perform this repair.

A deck wheel that drags, wobbles, or has a flat spot may no longer protect the turf correctly. The smooth roller touches the ground when the mower deck passes over a raised area, helping prevent the blade from cutting deep patches. Check deck level and tire pressure first because poor adjustment can also cause scalping. Match the replacem...Read moreent using the complete mower model and serial number, and compare the bore, width, bracket spacing, and required hardware. Shut off the engine, remove the key, set the parking brake, and disconnect the spark plug before service. Support the deck securely, tighten the fastener properly, and make sure the wheel turns freely.

This is an authentic Kawasaki replacement part at has been OEM sourced and is intended to be used with small engines. The gasket is used to seal the connection between the cylinder and the head assembly. This item is available as an individual replacement part, please note two gaskets may be needed.

This is an genuine Kawasaki replacement part manufactured for use with four stroke engines. This metal guide plate is the used to direct the push rods. This guide plate is sold individually, most engines require two, please see model diagram for additional parts.

This breather and gasket kit is a genuine OEM replacement designed for Kawasaki FH-series 4-stroke engines commonly used in lawn mowers and commercial turf equipment. It seals the crankcase breather system to properly regulate internal pressure while preventing oil leaks and blow-by. Supplied as a complete kit with the breather cover, gas...Read moreket, and mounting hardware, it’s an ideal replacement when oil seepage, excessive crankcase pressure, or breather damage affects engine cleanliness and reliable operation.

This is an authentic replacement part manufactured for use with Toro snowthrowers. The special hex head screw is used with a variety of different snowthrower models and has multiple applications. This screw is available as an individual replacement part, please see model diagram for associative parts.