7348B Frigidaire Dryer - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
belt came off
1 of 3 people
found this instruction helpful.
-
Justin from Hueytown, AL
- Really Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
removed front of drier , removed rear access panel, replaced the belt. reinstalled front of drier and rear access panel
Was this helpful?
Thank you for voting!
The drum belt was making a squealing noise, and it looked frayed.
1 of 3 people
found this instruction helpful.
-
Margery from Hartland, ME
- Really Easy
- 15 - 30 mins
-
Screw drivers, Socket set
After watching the video that explained and showed how to replace the bearing assembly, installation was a breeze. Great company to do business with. Ordered the part and had it in two days, and the dryer was working again asap. Thanks PartSelect
PS this dryer is 23 years old.
PS this dryer is 23 years old.
Was this helpful?
Thank you for voting!
belt squeking.
0 of 1 people
found this instruction helpful.
-
Eugenio from Lewiston, ME
- Really Easy
- 15 - 30 mins
-
Nutdriver
Replaced belt
Was this helpful?
Thank you for voting!
The drum belt was making a squealing noise, and it looked frayed.
0 of 1 people
found this instruction helpful.
-
Margery from Hartland, ME
- Easy
- 15 - 30 mins
-
Screw drivers, Socket set
Had to remove the front of the dryer but installation was quick and easy. An affordable and quick repair.
Was this helpful?
Thank you for voting!
Squeaking noise as the drum turned
0 of 1 people
found this instruction helpful.
-
Doug from Silver City, NM
- Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
I love technology. First thing I did was google on "U-tube", "How to repair a squeaking dryer". Several videos out there so I just found the one I needed and watched. The repair itself went easy. A word of advice would be to be careful of sharp edges and to remember to unplug the machine prior to repair. While the drum is out, go ahead an
... Read more
d get your shop vac and clean the inside of the unit out. Also, not only put grease on the new plastic holder, but put some on the shaft of the idler puller. I also used an awl to line up the holes on the front panel when re-installing the screws. One video I watched showed reaching in through the front to take the drum belt off the pulley, where another showed removing the inspection plate on the back. This made it much easier.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
the drum was making wierd sounds like it was a worn out bearing
0 of 1 people
found this instruction helpful.
-
Timothy from Green River, WY
- Really Easy
- 15 - 30 mins
-
Screw drivers, Wrench set
i took apart the dryer and then took out the drum from the inside and then put the new bearing in and put everything back in
Was this helpful?
Thank you for voting!
off balance and noisy operation
0 of 1 people
found this instruction helpful.
-
Justin from Opelousas, LA
- Really Easy
- 15 - 30 mins
-
Screw drivers, Socket set
removed the drum out the front and replaced
Was this helpful?
Thank you for voting!
Loud Squeeking
0 of 1 people
found this instruction helpful.
-
Jeffrey from League City, TX
- Really Easy
- 15 - 30 mins
-
Screw drivers, Socket set
First, used a putty knife to open the top of the dryer. Second, unscrewed the front panel and removed it by pulling up and out. The drum drops down slightly after doing this. Third, open the back grating and disconnect the belt from the motor and idle pulley. Fourth, Pull the drum (with belt) out through the front opening. Jerk up HARD on
... Read more
the back of the drum to disconnect it from the bearing seat. Fifth, replace bearing parts and seat according to diagram. I found it very difficult to unscrew the bearing axle from the drum. Had to hold down the drum and press hard to get screws to turn without stripping. Finally, put back together in reverse, don't forget to put A LOT of grease in your new bearing seat before reconnecting.
Read less
Was this helpful?
Thank you for voting!
Dryer drum would not turn.
0 of 1 people
found this instruction helpful.
-
Gregory from Prattsburgh, NY
- Really Easy
- 15 - 30 mins
-
Nutdriver, Pliers, Screw drivers
The first part was the most difficult-opening the front of the dryer cabinet! Once open, the new belt was installed and then the new idler pulley was put in-place. The cabinet was closed-job done.
Other Parts Used:
Was this helpful?
Thank you for voting!
Drum Squeeking
0 of 1 people
found this instruction helpful.
-
Mark from Aurora, IL
- Really Easy
- 15 - 30 mins
-
Nutdriver, Socket set, Wrench (Adjustable)
Replace the Drum Bearing and Shaft
Was this helpful?
Thank you for voting!
The dryer tub started screeching and then dropped.
0 of 1 people
found this instruction helpful.
-
Gloria from Murfreesboro, TN
- Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
Removed the top of the dryer above the dryer door by pulling the pop out plastic holds. I then removed the dryer plug in at the top inside dryer that controls the start when dryer door is closed. I thenremoved the screws that are located at the back of the dryer tub where the bearing is located. I then replaced the support bearing. I j
... Read more
ust replaced every thing I took off in reverse.
Read less
Was this helpful?
Thank you for voting!
Dryer was making LOUD, constant squeal while running
0 of 1 people
found this instruction helpful.
-
Robert from Millington, TN
- Easy
- 30 - 60 mins
-
Screw drivers, Socket set
Followed others directions and it went very well. I could not believe how much lint was packed in the bottom of the dryer! Need to clean this area out perhaps once a year.
Was this helpful?
Thank you for voting!
loud scratchy noise
0 of 1 people
found this instruction helpful.
-
david from edinboro, PA
- Really Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
first and foremost, watching video on replacement/repair was key to success.furthermore, i ordered part one day and was at my doorstep the following day. the installation process took approximately half of an hour which included vaccuuming cabinet of lint.
Was this helpful?
Thank you for voting!
Broken Part
0 of 1 people
found this instruction helpful.
-
william from fairfield, PA
- Really Easy
- 15 - 30 mins
-
Screw drivers
Really easy. 15 Minutes.
Was this helpful?
Thank you for voting!
Old dryer lint screen had a hole.
0 of 1 people
found this instruction helpful.
-
Raymond from La Crosse, WI
- Really Easy
- Less than 15 mins
Pulled out old screen (exactly like what you do to empty it), put in new one....
Was this helpful?
Thank you for voting!