72186013010 Kenmore Microwave - Parts

This is a single grease filter manufactured for a microwave. The microwave grease filter filters the exhaust air and traps any grease flowing out of the appliance. It is important to keep the filter clean and intact by cleaning it regularly and replacing it when needed. A clogged air filter can cause your appliance to run inefficiently an...Read mored possibly alter the taste and smell of your food. This filter is approximately 7.5 inches wide and 5 inches deep. This part is sold separately. No tools are required for this repair, the filter simply slides in and out using the easy-pull tab on the filter.

This microwave door switch provides power to the various components in the microwave when the door is in a closed position, and interrupts power when the door is open. This door switch is approximately 1 1/2 inches long, and has 2 metal prongs called terminals that extend from its body. If your microwave will not turn or heat properly, th...Read moreere could be an issue with the door switch. You can check the switch for continuity using a multi-meter. With the actuator button depressed, you should see continuity between these terminals. If there is no continuity the switch will need to be replaced. NOTE: Before you begin this repair, first make sure your microwave is unplugged, and that your capacitor is discharged. A capacitor stores large amounts of electricity even when your microwave is unplugged.

This is a single grease filter manufactured for a microwave. The microwave grease filter filters the exhaust air and traps any grease flowing out of the appliance. It is important to keep the filter clean and intact by cleaning it regularly and replacing it when needed. A clogged air filter can cause your appliance to run inefficiently an...Read mored possibly alter the taste and smell of your food. This filter is approximately 7.5 inches wide and 5 inches deep. This part is sold separately. No tools are required for this repair, the filter simply slides in and out using the easy-pull tab on the filter.

This is an authentic LG charcoal filter for your microwave, sourced directly from the manufacturer. It is designed to remove odors from the air that circulate through your microwave vent. It measures approximately 11 inches in length, and 2.5 inches in width.

The range thermostat is also commonly known as a stove, oven, cooktop, or range thermal fuse. This thermostat protects your oven from excessive heating, and will shut the oven heat off if excessive heating is detected. This is a genuine part sourced directly from the original manufacturer. You may need to replace this part if your applian...Read morece will not heat properly. It is made of metal and is approximately 1 inch in diameter. This part is sold individually. It is recommended to order a spare, especially if you commonly use the self-cleaning function in your oven.

This bracket holds the metal or plastic flapper that closes off the exhaust duct when the fan is not running and opens when the fan turns on. If the exhaust fan on your microwave does not appear to be working, the problem may be with the damper assembly. If the damper does not open and close easily, check for any damage to the bracket, an...Read mored replace if it is damaged or faulty. This genuine OEM exhaust damper measures approximately 12 inches long by 5 inches wide.

This metal vent damper door closes off the exhaust duct when the fan is not running to stop outside air from entering the microwave unit, and opens when the fan turns on to allow air to vent away from the microwave. This vent damper door measures approximately 10 inches long x 3 inches wide and fits LG microwaves.

The fuse-time delay may also be known as a line fuse or a microwave fuse, and it is a piece for your microwave. The function of this part is to shut off the microwave if there is a power surge, in order to protect your microwave from damage. You should consider having a service technician install this part as the high-voltage capacitors i...Read moren a microwave can contain a very harmful electrical charge, even when the microwave is unplugged and has been inactive for some time. The tools that would be needed to complete this installation include a Phillips screwdriver, an insulated screwdriver, and a pair of pliers.

This is a halogen lamp, or light bulb, for a microwave. The microwave light should illuminate the inside of the microwave while the door is open and while the appliance is running. If the light bulb does not illuminate, you may need to replace it. This part is sold individually. It is a common wear part and does not have a standard light ...Read morebulb base, so consider ordering a spare. This part is made of clear glass. If the glass on the existing light bulb is broken, you may need to use a pair of needle nose pliers to remove it. Be sure to handle the broken part with work gloves and disconnect power to the appliance before changing the bulb.

If the turntable on your microwave does not rotate, or you can hear a grinding noise, the problem may be with the motor. The motor is typically located below the floor of the oven, and is accessed through the bottom. The motor is normally held in place with a retaining screw and will have two wires attached to it as well. If the motor is ...Read moremaking a grinding noise it will need to be replaced. If the motor does not turn, you can check for voltage or continuity with a multi-meter. Make sure the power is disconnected from your microwave before beginning this repair.

Usually found kitchen appliances, this OEM-certified diode cable assembly helps to convert power from the transformer to the magnetron, to heat up your food. A damaged cable assembly will cause your appliance to heat food inconsistently or to not work at all. You might notice a burning smell or a loud buzzing sound coming from your applia...Read morence. If you do not replace a broken cable assembly, the components that produce heat in your appliance can overheat and fail. To replace your cable assembly, start by unplugging your appliance from any electrical source. Remove any protective casing from the assembly by unthreading any screws or clips. Disconnect the cable assembly from the transformer and the magnetron with pliers. Reinstalling a new cable assembly requires you to reverse the previous steps. Please keep in mind that this cable assembly is sold individually.