72093 (ASTCSE0) LG Refrigerator - Instructions

For the right side of the refrigerator door, just pulled off the old gasket and replaced it with the new one. Old gasket came off easily. Just had to pull it off. No screws on the right side. Just pushed the new one in place in the groove on the door.

For the left side, needed a Phillip’s screwdriver to remove the flap first. H ... Read more elps to have a second person hold the door from moving. Once flap was off, pulled the old gasket off and installed the new one just like the right side. Then screwed the flap back on once the gasket was in the groove properly.

Initially after install, it seemed like the magnet on the door was not strong enough but after a couple of days, the magnet seems a lot stronger, sealing the air out. Very happy I replaced it. It was a lot simpler to replace than I thought it would be.

Once I U tubed the the removal and replacement of the gaskets it was super easy. The right gasket change was easy without tools. The left gasket required me to remove the mullion first, which is why I used Utube.

Followed directions that came with the filter. Did remove the top shelf for easier access. Very simple and quick.

Removed 4 screws then removed ice maker unit. Unplugged the old unit. Checked and verified the inlet tube was clean and not blocked. Plugged in the new unit. Placed unit into proper location and verified it was properly in place. Replaced the 4screws. Turned on the unit closed the ice door and it started making ice maybe an hour later by ... Read more morning the ice bucket was full. Super easy.

Watch YouTube videos on this topic if you are uncertain before tackling the job. The right door was easy to replace. Just pull the gasket with your fingers and it will come off easily. Place new gasket over door and use fingers to press it inside the groove few inches at a time. Pay attention to gasket orientation.

The left ... Read more door is a bit harder because you need to remove the mullion at the door edge using a screw driver. Remove two screws on the center hinge and then slide the mullion up to disengage. Then unplug the wires to remove the mullion. Replace the gasket as described above and replace the mullion reversing the directions shown above.

Could not believe how easy it was!

I installed the new 3 wire ice maker very easily, but it was defective. I was told that instructions for the return of the defective part would be sent later due to the virus. I have never received the return instruction.
I did receive a credit for the defective part. VERY Satisfied with y’all’s service.
Waiting for return i ... Read more nstructions if y’all still want it back.
Thanks,
Thomas Pennebaker

Fortunately, others had left comments about this installation, so proved very helpful. First thing was laying out the gasket flag on the counter to allow it to unbend, get out the kinks from shipping. While the new gasket was laying out on the counter, started removing the old gasket. As it had been there for 11 years, needed pliers to ... Read more get a corner started. I was slow and careful removing the old gasket in case I needed to put it back in. A very helpful suggestion from others was to lightly rub dishwashing soap on the gasket edge that fits in the groove in the door. Again, slow and careful, got it installed, wiped off any excess dishwashing liquid, and the door closed with a better seal in a long time. Pleasantly surprised how easy this was to do!

Took off the French door Mullen by unscrewing middle area. Unconnected the wires for the door sensor. Then detached old gasket and replaced with new gasket. Reattached the wiring and snapped Mullen flap in place and finally rescrewed to the door. Seal is very good now.

Some have said that the installation took 5 minutes. Mine took less than that, and I did it with one hand. I had a beer in my other hand.

Part Select had a great video which made the repair easy, using a putty knife to start removing the freeze door gasket. Once removed the install is simple just snap the new gasket into the track, but start at the corner. Other company's have a video requiring you to remove the entire freezer compartment out of the appliance, unnecessary w ... Read more aste of time and labor.

Watched a couple of YouTube videos and then went at it

Un-wrapped the basket......Installed with NO tools......

Opened the box. Removed wrapping. Washed the new part. Unloaded old basket. Removed old basket. Set in new basket. Loaded new basket. Closed the door. Even an 80 year old can do it!

Simply removed old gasket. Started in a corner with installing the new gasket. It went in easily and quickly.

Removed the old one and replaced with the new.