My Orders
72092 (ASWCSE1) LG Refrigerator - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Water feed line running from water valve to filter housing was leaking
13 of 21 people
found this instruction helpful.
-
Tom from EASTON, PA
- Easy
- 30 - 60 mins
-
Screw drivers, Wrench (Adjustable)
Shut off water supply. Disconnect main supply line. Remove rear lower panel on back of refrigerator. Remove all tubing clamps on back. Disconnect leaking tubing from water supply valve. Remove water filter and unscrew/remove water filter housing. Replace tubing - connect to water filter housing then to water supply valve. Reconnect filter
... Read more
housing and filter. Reinstall lower panel, then main water supply line, then all tubing clamps. Turn water back on and check for leaks after discarding several glasses of water to fill filter. Job complete!
Read less
Was this helpful?
Thank you for voting!
Fridge waterline for ice maker / door water
6 of 8 people
found this instruction helpful.
-
Todd from MARS HILL, NC
- Really Easy
- Less than 15 mins
-
Screw drivers
The heavy work is moving the fridge, then take off the lower plans. Use a bowel or cup for screws and the water line connector spacers so you don't loos them.
undo connections holding water line, including the bottom brakes for the solenoid. Reuse the spring around the lower waterline to prevent external wear on the line.
... Read more r />NOTE: remove the waterline connector spacers and save!
NOTE: you must compress (not pull) the connect to then pull the waterline out of the connectors.
NOTE: You must also remove the water filter and housing inside the fridge but this is easy.
MOTE: Test the line for leaks by turning on the water and then using the door water. The filter will need to refill so it may take a minute before water comes up. This line only have pressure when the door water is used or the ice maker needs to make ice.
After replacing the line, test the line for leaks by using the door water so the solenoid fills the lines
undo connections holding water line, including the bottom brakes for the solenoid. Reuse the spring around the lower waterline to prevent external wear on the line.
... Read more r />NOTE: remove the waterline connector spacers and save!
NOTE: you must compress (not pull) the connect to then pull the waterline out of the connectors.
NOTE: You must also remove the water filter and housing inside the fridge but this is easy.
MOTE: Test the line for leaks by turning on the water and then using the door water. The filter will need to refill so it may take a minute before water comes up. This line only have pressure when the door water is used or the ice maker needs to make ice.
After replacing the line, test the line for leaks by using the door water so the solenoid fills the lines
Read less
Was this helpful?
Thank you for voting!
Filter housing leaking
4 of 4 people
found this instruction helpful.
-
Larry from CLEMMONS, NC
- Really Easy
- 30 - 60 mins
Removed old filter head, installed the new head
Was this helpful?
Thank you for voting!
Changing out the Ice Maker tube
9 of 19 people
found this instruction helpful.
-
HARRY from SPARKS, NV
- Really Easy
- 15 - 30 mins
-
Screw drivers, Wrench (Adjustable)
An easy way to get a refrigerator out from the wall is to use a tow strap or 1/2 to 3/4 in. rope. Throw a loop behind refer while keeping both ends in your hands. Let it settle down to the lower half of unit and pull using both hands. Comes right out.
Remove lower panel. Unscrew water valve from cabinet. Remove all tube holders L ... Read more ay some rags down to catch a little water drainage.
Turn off water supply valve at wall. Unplug Power. Remove filter and filter holder. (one screw).
remove tube from valve by removing plastic C clip. Push plastic ring towards the valve and pull out tube at same time.
With the tube free, remove filter, then mount screw to remove the inside filter holder. When it is out, pull the tube doing the same process as the lower end. Pull tube out and replace with new one putting everything back in reverse order.
Before placing tube holders back on, turn on water to check for leaks.
After turning water back on and plugging in power, push refer back into place.
While I was there, I also replaced the hose from the wall to the refer.
Remove lower panel. Unscrew water valve from cabinet. Remove all tube holders L ... Read more ay some rags down to catch a little water drainage.
Turn off water supply valve at wall. Unplug Power. Remove filter and filter holder. (one screw).
remove tube from valve by removing plastic C clip. Push plastic ring towards the valve and pull out tube at same time.
With the tube free, remove filter, then mount screw to remove the inside filter holder. When it is out, pull the tube doing the same process as the lower end. Pull tube out and replace with new one putting everything back in reverse order.
Before placing tube holders back on, turn on water to check for leaks.
After turning water back on and plugging in power, push refer back into place.
While I was there, I also replaced the hose from the wall to the refer.
Read less
Was this helpful?
Thank you for voting!
Ice maker needed replaced
3 of 3 people
found this instruction helpful.
-
Lee from BELTON, TX
- Very Easy
- Less than 15 mins
-
Screw drivers
Removed 4 screws then removed ice maker unit. Unplugged the old unit. Checked and verified the inlet tube was clean and not blocked. Plugged in the new unit. Placed unit into proper location and verified it was properly in place. Replaced the 4screws. Turned on the unit closed the ice door and it started making ice maybe an hour later by
... Read more
morning the ice bucket was full. Super easy.
Read less
Was this helpful?
Thank you for voting!
Ice maker wore out.
3 of 3 people
found this instruction helpful.
-
Thomas from LA PLACE, LA
- Really Easy
- 30 - 60 mins
-
Screw drivers
I installed the new 3 wire ice maker very easily, but it was defective. I was told that instructions for the return of the defective part would be sent later due to the virus. I have never received the return instruction.
I did receive a credit for the defective part. VERY Satisfied with y’all’s service.
Waiting for return i ... Read more nstructions if y’all still want it back.
Thanks,
Thomas Pennebaker
I did receive a credit for the defective part. VERY Satisfied with y’all’s service.
Waiting for return i ... Read more nstructions if y’all still want it back.
Thanks,
Thomas Pennebaker
Read less
Was this helpful?
Thank you for voting!
Replace water filter
4 of 6 people
found this instruction helpful.
-
Bill from FORT SMITH, AR
- Very Easy
- Less than 15 mins
Followed directions that came with the filter. Did remove the top shelf for easier access. Very simple and quick.
Was this helpful?
Thank you for voting!
Left side gasket was torn and would seal properly
3 of 4 people
found this instruction helpful.
-
Thomas from CHULA VISTA, CA
- Easy
- Less than 15 mins
-
Screw drivers
Took off the French door Mullen by unscrewing middle area. Unconnected the wires for the door sensor. Then detached old gasket and replaced with new gasket. Reattached the wiring and snapped Mullen flap in place and finally rescrewed to the door. Seal is very good now.
Was this helpful?
Thank you for voting!
Icing up in the freezer due to poor gasket
2 of 2 people
found this instruction helpful.
-
Maryann from BROOKFIELD, IL
- Really Easy
- Less than 15 mins
-
Screw drivers
Watched a couple of YouTube videos and then went at it
Was this helpful?
Thank you for voting!
Ice crystals appearing on the face of the freezer draws
2 of 2 people
found this instruction helpful.
-
Craig from SPRING HILL, FL
- Really Easy
- Less than 15 mins
Part Select had a great video which made the repair easy, using a putty knife to start removing the freeze door gasket. Once removed the install is simple just snap the new gasket into the track, but start at the corner. Other company's have a video requiring you to remove the entire freezer compartment out of the appliance, unnecessary w
... Read more
aste of time and labor.
Read less
Was this helpful?
Thank you for voting!
The shelf on our refrigerator was cracked so I ordered a replacement.
3 of 5 people
found this instruction helpful.
-
Scott from KENT, WA
- Very Easy
- Less than 15 mins
Some have said that the installation took 5 minutes. Mine took less than that, and I did it with one hand. I had a beer in my other hand.
Was this helpful?
Thank you for voting!
Replaced hose and it was exactly what I needed.
3 of 5 people
found this instruction helpful.
-
Donald from CLEBURNE, TX
- Very Easy
- 30 - 60 mins
-
Screw drivers
Replaced old hose and installed the new one. Was very simple with the instructions in your email..... step by step, could not of been any similar.... you guys rock
Was this helpful?
Thank you for voting!
Broken Door Basket
2 of 3 people
found this instruction helpful.
-
Theodore from SACRAMENTO, CA
- Very Easy
- Less than 15 mins
Un-wrapped the basket......Installed with NO tools......
Was this helpful?
Thank you for voting!
Plastic bracket holding freezer drawer broke off
1 person
found this instruction helpful.
-
Terry from Broken Arrow, OK
- Very Easy
- Less than 15 mins
-
Screw drivers
Removed upper drawer/basket from freezer
Removed 2 Philips screws
Removed rail bracket assembly
Reinstalled reversing those steps
Works like new.
Happy wife. Happy life. FYI- I am nearly 77 yrs young.
Removed 2 Philips screws
Removed rail bracket assembly
Reinstalled reversing those steps
Works like new.
Happy wife. Happy life. FYI- I am nearly 77 yrs young.
Was this helpful?
Thank you for voting!
Door basket broke
1 person
found this instruction helpful.
-
FONDA from KATY, TX
- Very Easy
- Less than 15 mins
Opened the box. Removed wrapping. Washed the new part. Unloaded old basket. Removed old basket. Set in new basket. Loaded new basket. Closed the door. Even an 80 year old can do it!
Was this helpful?
Thank you for voting!