Add useful storage space inside a refrigerator door with this clear plastic door bin. It holds bottles, jars, drinks, and condiments where they are easy to see and reach. The bin measures about 13-1/2 inches wide and 4-1/4 inches high. Its shaped base is about 9-1/2 inches deep on one side and 10-1/8 inches deep on the other. Installation...Read more requires no tools. Place the bin slightly above the mounting points, then slide it down until it locks into place. Compare the size, shape, and side mounts with the original bin before ordering.
This handle screw, also known as a mounting bolt, is a mounting screw to help secure the door handle to your refrigerator door. If your handle is loose, you may just need to tighten the screw. If your screw is missing or broken, it may need to be replaced. There are multiple handle screws on your fridge, please consider ordering extra as ...Read morethey commonly wear at the same rate. This is about 1 inch long and metallic in color.
This refrigerator door bin provides handy storage for condiments, jars, bottles, and other small items. It attaches to the inside of the door, keeping everyday foods easy to reach while freeing up space on the main shelves. The raised sides help keep items in place as the door opens and closes. Cracks, broken mounting tabs, or a damaged b...Read morease may leave the bin loose or unable to hold items safely. Replacing a broken bin restores useful storage and helps keep your refrigerator organized. This is an OEM part sourced directly from the manufacturer.
This air filter assembly is a genuine replacement part designed to improve air quality inside select LG and Kenmore Elite refrigerators. Using activated carbon, it effectively traps and neutralizes odors and airborne impurities, helping maintain a clean environment that supports longer food freshness. The filter is housed within a dedicat...Read moreed compartment and should be replaced approximately every six months or when indicated by the refrigerator’s filter light. Installation involves locating the filter housing, powering off the appliance, removing the old filter, and inserting the new one with proper alignment. After installation, reassemble the housing, restore power, and reset the filter indicator to ensure accurate tracking. This OEM component ensures a precise fit and optimal performance for compatible models.
This is a manufacturer-approved refrigerator door closure for your refrigerator. It is made of white plastic and measures approximately 3 inches by 2 inches. If your old closure is damaged, your refrigerator door may not open and shut properly, and therefore it should be replaced.
This is a micro switch for various models of LG refrigerators. This switch is responsible for turning the ice dispenser on and off within the freezer compartment of the fridge. If this switch is damaged or shorted, it will cause the ice maker to work inconsistently, or not at all. This switch is different from the water dispenser switch, ...Read morewhich has an entirely different shape all together. Replacing this switch is simple and only requires a Philips-head screwdriver to disconnect the old switch and install the new one. This switch is a genuine OEM LG part and does not come with any other parts or accessories.
Water cools inside the refrigerator before dispensing with help from this reservoir tank assembly. The tank holds a supply of water in the fresh food compartment, allowing it to chill between uses. Cracks, punctures, or damaged connections may cause leaks inside the cabinet and interrupt delivery to the dispenser. Replacing a damaged rese...Read morervoir restores the enclosed storage path for chilled water. As water leaves the tank during dispensing, incoming water replenishes the supply so it can cool before the next use. This is an OEM part sourced directly from the manufacturer.
NOTE: The Secondary (smaller) wire connector has 3 wires in it. If original ice maker has 6 wire connector see part number AEQ73110205. Please verify connector before ordering.
Dispensing water and filling the ice maker require controlled flow through this refrigerator water inlet valve assembly. Electrically operated solenoids open the water passages when requested by the appliance controls and close them when delivery ends. A cracked or faulty valve may leak, restrict dispenser flow, or prevent the ice maker f...Read morerom receiving enough water. Replacing a failed assembly helps restore reliable water routing and proper shutoff between requests. It connects the incoming supply to the internal water circuits used during everyday dispensing and ice production. This is an OEM part sourced directly from the manufacturer.
This water tubing clip holds the water fill tube in place in your refrigerator. The water fill tube attaches and supplies water to the ice maker/water dispenser in your fridge-freezer. If the tubing is in working order, but is hanging loose inside the unit, the issue could be that the clip meant to hold it in place is broken. If this is t...Read morehe case, you should look to replace the clip. This clip is made of black plastic, and is just over half an inch long. This is a genuine OEM replacement part, and is sold separately.
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Ice maker needed replaced
4 of 4 peoplefound this instruction helpful.
Lee from BELTON, TX
Very Easy
Less than 15 mins
Screw drivers
Removed 4 screws then removed ice maker unit. Unplugged the old unit. Checked and verified the inlet tube was clean and not blocked. Plugged in the new unit. Placed unit into proper location and verified it was properly in place. Replaced the 4screws. Turned on the unit closed the ice door and it started making ice maybe an hour later by
... Read moremorning the ice bucket was full. Super easy.
Read less
Was this helpful?
Thank you for voting!
Ice maker wore out.
3 of 3 peoplefound this instruction helpful.
Thomas from LA PLACE, LA
Really Easy
30 - 60 mins
Screw drivers
I installed the new 3 wire ice maker very easily, but it was defective. I was told that instructions for the return of the defective part would be sent later due to the virus. I have never received the return instruction. I did receive a credit for the defective part. VERY Satisfied with y’all’s service. Waiting for return i
... Read morenstructions if y’all still want it back. Thanks, Thomas Pennebaker
Read less
Was this helpful?
Thank you for voting!
The shelf on our refrigerator was cracked so I ordered a replacement.
3 of 5 peoplefound this instruction helpful.
Scott from KENT, WA
Very Easy
Less than 15 mins
Some have said that the installation took 5 minutes. Mine took less than that, and I did it with one hand. I had a beer in my other hand.