71553 (ASTESEU) LG Dryer - Instructions

Initially replaced igniter. Didn't think it was bad though. Read other suggestions on another website. None were the correct diagnosis for my situation. And when I figured it out they did not offer correct part. The dryer thermistor temp sensor (probe sensor) is what I replaced. Found it on Parts Select. I did replace other parts also. Bu ... Read more t that's the one that ultimately was the issue.
Was not hard at all if one is even a little handy.

Removed the old damaged filter and replaced it a new one.

Take old one out and slide new filter in.

Put the new lint filter in and it was completed

Pull off the top and front of the dryer and reached in and replaced the part it was easy. Had to clean all the dryer out real good with from the lint

Opening the dryer door on the vertical axis rather than the horizontal axis, I unscrewed the three obvious screws. These screws are clearly visible when viewed from eye level. The broken hinge came off in two pieces, but presented no difficulty. I inspected the area around the hinge for auxiliary damage. There was none, but I did noti ... Read more ce a wisp of cotton candy stuck in the lint trap. This was odd as I had not had cotton candy of any kind in my home or near my dryer ever. I did hear the faint sound of calliope music-I assumed this to be from an ice cream van that frequents the neighborhood-but failed to detect the tell-tale doppler effect of a moving vehicle. Disturbed, but determined to finish my task I removed the new part from the packaging and checked the fit. It fit perfectly. NOTE: Retain the screws from the hinge you remove, as the replacement hinge does not come with screws. I looked down to where my screws lay and saw the bulbous oversized toe of large red shoe. There was a star on the tip, painted in blue and yellow. I looked up from the shoe to see it attached to an ankle with a frilled cuff and up from there a baggy pair of pantaloons. At this point I realized that circuses now being illegal in this country, I clearly had a rogue clown on my hands. Sitting as I was I was not able to quickly get up, and in the confines of my washroom I had nowhere to run anyway. I had to think fast. I could smell the stale popcorn on the clown's breath as he leaned over, I reached for anything I could, grabbing up a pet cleaning vacuum hose. The clown just snorted and said, "You want a Phillip's head for that." The clown was right, of course. I installed the screws, checked that the door worked, and then the clown and I went for churros.

I replaced the thermistor, then the gas ignitor which were easy to get to once the drum was out. The gas is still not igniting so not sure where to go from here. Putting the drum belt back on took some muscle. But then I'm 71.

With a thin flat screwdriver I was able to pry out the old door switch, I replaced it with the new door switch, pushed back in dryer and so far is working since I installed a month ago.

Called LG on the phone and they gave the button presses for diagnostics, which then gave the HST code, saying the Humidity sensor was bad.
The part was described as the Humidity sensor module. Actually it's just the wire leads for the sensor which must be electronic and only accessible by disassembling the dryer. There were descr ... Read more iptions about cleaning the wires, perhaps because some people use dryer sheets which cause a buildup on the wires and prevent them from doing their job. I use wool balls and have no buildup on my wires and replacing them did not fix the sensor, because the module accessible inside the dryer is not the moisture sensor, but only the wire leads.

Repair was easy, but the part does not come with directions. It is pretty self explanatory if you are used to taking things apart and fixing them. Otherwise there are YouTube videos you can pull up. Dryer runs like it is new again though and it was way cheaper than buying a new dryer.

Exchange

Followed the instruction on video.was great after three parts now is OK .we have heat.still cheaper than having it service.

There’s all sorts of videos on it I watched. It was actually very simple

Completely had to dismantle the dryer to get to the igniter.
The screw holding the igniter is a SOB to get at for extraction, and even worse putting back.,

Ordered a new Dryer Lint Filter Assembly that fit my LG electric dryer.