71463 (ASTESEU) LG Dryer - Parts

This part is sold individually. The drum support roller is found in your dryer. It is used to hold the drum in place in the cabinet while letting the drum rotate on the support rollers. It is recommended that you replace both rollers at once. You may notice that this part needs to be replaced if you are experiencing a squeaking noise, whi...Read morech could be due to the bearing going bad. The bearing could be severely damaged if you hear a very loud thumping noise, much like you would when you are drying a pair of shoes.

This lint filter is designed to capture loose lint during dryer operation, helping maintain airflow and drying efficiency. Positioned within the dryer drum, it plays a vital role in preventing lint buildup that can affect performance or pose a fire risk. Over time, the filter may become clogged or damaged due to regular use. Constructed w...Read moreith a white plastic frame and fine mesh screen, this replacement filter is sold individually and is compatible with select dryer models. Installation is simple and tool-free: remove the old filter and insert the new one into the designated slot to restore optimal function.

The belt wraps the length of the dryer drum, secured by a tension pulley and then loops around the motor pulley. If you find that the drum is not turning properly or at all while your dryer is in succession, it might be due to the belt being broken.

This dryer thermistor temperature sensor helps monitor and regulate the temperature inside a dryer. This part includes the wire harness. If your dryer overheats, does not produce enough heat, or takes too long to dry, then the thermistor might be defective or damaged. This can cause a fault code and could begin either prolonging or shorte...Read morening drying time. As a safety precaution, make sure to unplug the dryer from the power source before beginning this installation, and wear gloves to protect your hands. Refer to the installation instructions provided by the manufacturer for further guidance.

The thermostat is a part for your dryer, and it is roughly 1 inch long by roughly 1.5 inches wide. The purpose of the thermostat is to measure the temperature of the air inside your dryer drum. As the air is being measured, it will turn the heat on or off in order to maintain a stable temperature within the drum. The most common reason yo...Read moreu would need to replace your thermostat is if your dryer is not receiving enough heat, or any heat at all.The tools you will need to complete this repair include a Phillips screwdriver, and a flat-head screwdriver.

This dryer thermistor temperature sensor helps monitor and regulate the temperature inside a dryer. This part includes the wire harness. If your dryer overheats, does not produce enough heat, or takes too long to dry, then the thermistor might be defective or damaged. This can cause a fault code and could begin either prolonging or shorte...Read morening drying time. As a safety precaution, make sure to unplug the dryer from the power source before beginning this installation, and wear gloves to protect your hands. Refer to the installation instructions provided by the manufacturer for further guidance.

This is an OEM lint filter guide cover made for LG dryers. This is one of three pieces in the entire lint filter assembly, along with the lint filter guide and filter itself, which are both sold separately from this. This guide cover is made entirely of plastic and measures approximately 16 inches wide. If the lint filter assembly for you...Read morer dryer is broken, chipped, or cracked, and ultimately cannot perform efficiently anymore, covers like this must be replaced immediately. This cover comes individually and without any accompanying parts, so be sure to check your lint filter assembly for the necessary parts before ordering.

This spiral-style gas burner igniter is designed for use in select gas dryers and plays a crucial role in generating the heat needed to dry clothes. Operating at 120 volts, the igniter glows red hot during the drying cycle to ignite the gas that heats the drum. If your dryer runs but fails to produce heat, the igniter may be faulty and sh...Read moreould be replaced. The assembly includes the igniter, bracket, wire harness, and plug for straightforward installation. Always disconnect the dryer from power before beginning any repairs to ensure safety.

This genuine OEM conversion kit allows your dryer to be converted from using natural gas to liquid propane. It caters to homes that rely on propane for their energy needs. This kit comes with an orifice that controls the flow rate of propane gas, and replaces the one originally installed on the gas burner in your dryer. This kit is sold i...Read morendividually. Proceed with caution when installing it yourself to ensure safe and proper installation.

This genuine OEM felt gasket provides a cushioned seal between the inner tub of your electric dryer and the rear panel. It prevents your clothes from getting snagged and helps in heat retention. You will find it around the circumference of the drum. The most typical reason for replacing the felt seal is when it becomes worn. It is importa...Read morent to note that this rear seal is sold separately from the front seal and the adhesive needed to install it.

This genuine OEM filter guide keeps garments from exhaust air duct and lint screen inside the dryer. The filter guide is made of high quality plastic and is approximately 15 inches long by 3 inches wide. If your filter guide is faulty, or damaged clothes can get stuck in the lint screen which can cause damage to your garments and to the d...Read moreryer unit itself. NOTE: Flap (PS3634953) and Spring (PS11706080) are sold separately.