Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Broken water line
53 of 72 peoplefound this instruction helpful.
Debbie from FISHER, AR
Really Easy
15 - 30 mins
Screw drivers
Remove water filter and water filter holder. Removed cover on back of frig. Removed clip where water line connects to back of water filter. Took half inch wrench pushed in on water line lock to release line. Repeat at other end. Reverse steps to put on new line. Easy repair.
Video makes it look easy. Kenmore refrigerator does not have "groove" along the right hand side of switch that allows for pushing down on release. Used a thin screwdriver to get under to push while holding switch edge with pliers. Kept slipping. Tape sides to avoid scratching inside of refrigerator.
Was this helpful?
Thank you for voting!
Water feed line running from water valve to filter housing was leaking
13 of 21 peoplefound this instruction helpful.
Tom from EASTON, PA
Easy
30 - 60 mins
Screw drivers, Wrench (Adjustable)
Shut off water supply. Disconnect main supply line. Remove rear lower panel on back of refrigerator. Remove all tubing clamps on back. Disconnect leaking tubing from water supply valve. Remove water filter and unscrew/remove water filter housing. Replace tubing - connect to water filter housing then to water supply valve. Reconnect filter
... Read more housing and filter. Reinstall lower panel, then main water supply line, then all tubing clamps. Turn water back on and check for leaks after discarding several glasses of water to fill filter. Job complete!
Read less
Was this helpful?
Thank you for voting!
Icemaker quit releasing ice from tray and water was pouring and freezing in ice storage bin
13 of 24 peoplefound this instruction helpful.
Amber from PEORIA, IL
Really Easy
15 - 30 mins
Screw drivers
This couldn't have been easier. Two tiny screws in the front needed unscrewed, and then two plastic clips in the middle just had to be popped lose. Finally, you unplugged the power cord. Then, you just needed to reverse the process by plugging the new ice maker in, popping the clips in place, and screwing the two holes back in and turning
... Read more the whole thing on. Voila! Perfect ice cubes again. And for only a little over $100.
Read less
Was this helpful?
Thank you for voting!
needed to replace broken ice maker
11 of 18 peoplefound this instruction helpful.
John from WEST ROCKPORT, ME
Very Easy
Less than 15 mins
Screw drivers
Take out 2 screws and unplug unit before removing. Plug-in new unit and screw in 2 screws. That's it.
Was this helpful?
Thank you for voting!
Water leaking from back of the refrigerator
8 of 12 peoplefound this instruction helpful.
Jason from PLEASANT HILL, CA
Really Easy
30 - 60 mins
Pliers, Screw drivers
Pretty simple fix.
1) Removed the screws from lower back plate 2) Removed the screws holding the plastic water lines in place (little plastic brackets - several of them) 3) Take a picture of how the tubing and what hose goes into what part - the 5/16" hose can go into 2 different spots - I didn't do this and I had to
... Read morefix this 4) Pull out the hose "tabs" that lock the clamp into place (several) 5) Push in new hose 6) Put in clamp 7) I had to remove the filter on the inside of the fridge. Remove the filter, there is one screw that comes out, then you will have access to the hose clamps 8) Repeat for all the other hoses 9) Put the plate and brackets back into place (the picture really helps on how to orient and route the 3 different tubes 10) Test the water 11) Crack open a beer for a job well done
Super easy - take a picture! It will save you time!
Icemaker flooded the storage container box for cubes. Then froze solid.
12 of 26 peoplefound this instruction helpful.
Irvin from Anaheim, CA
Really Easy
30 - 60 mins
Screw drivers
Ordered the Part after looking at the choices shown, once I inspected the unit. I then knew by looks what would fit. THEN (important) went on Utube asking for video instructions. They had it on the computer and it was just too easy. What took the longest was the removable of the frozen food items and the drawers in the Bottom Freezer sect
... Read moreion. Perfect product, perfect instructions, perfect job and worked perfectly!
Fridge only 18 months old too!
Handyman wanted $457.00 to do the job! HA.
Read less
Was this helpful?
Thank you for voting!
Remove and replace cracked crisper drawer cover frame
5 of 5 peoplefound this instruction helpful.
H Bartlett from JENSEN BEACH, FL
Really Easy
15 - 30 mins
Screw drivers
1) Remove three drawers and items sitting on glass shelf. 2) Remove glass shelf 3) Remove entire crisper plastic unit from refrig. 4) Unscrew 6 screws holding uprights with a philips head screwdriver. 5) Remove top frame and replace with new frame. 6) Replace 6 screws and tighten them. 7) Replace entire frame
... Read more in refrig and replace 3 drawers and glass shelf. 8) Done
Read less
Was this helpful?
Thank you for voting!
Warped and melted lamp cover
5 of 5 peoplefound this instruction helpful.
Brad from MUSCATINE, IA
Really Easy
Less than 15 mins
Screw drivers
Remove 2 screws and then disconnect wires to the bulb sockets. Reconnect the wires Reinstalled lamp case , tab end first then replaced the 2 screws and the Lens cover. In addition, I changed out the incandescent bulbs to a much cooler LED bulb.
The heavy work is moving the fridge, then take off the lower plans. Use a bowel or cup for screws and the water line connector spacers so you don't loos them. undo connections holding water line, including the bottom brakes for the solenoid. Reuse the spring around the lower waterline to prevent external wear on the line.
... Read morer />NOTE: remove the waterline connector spacers and save! NOTE: you must compress (not pull) the connect to then pull the waterline out of the connectors. NOTE: You must also remove the water filter and housing inside the fridge but this is easy. MOTE: Test the line for leaks by turning on the water and then using the door water. The filter will need to refill so it may take a minute before water comes up. This line only have pressure when the door water is used or the ice maker needs to make ice.
After replacing the line, test the line for leaks by using the door water so the solenoid fills the lines
Read less
Was this helpful?
Thank you for voting!
Ice maker quit working
5 of 6 peoplefound this instruction helpful.
Richard from MINNEAPOLIS, MN
Very Easy
Less than 15 mins
Screw drivers
Plug in the replacement ice maker to the socket in the frig, fit the back of the new ice maker into the slot to the rear, attach with 2 screws saved from removing old ice maker. Simple.
Was this helpful?
Thank you for voting!
Bad Push Button Switch
7 of 13 peoplefound this instruction helpful.
Dorothy from KINGMAN, AZ
Really Easy
Less than 15 mins
Pliers, Screw drivers
I followed the directions! It was so easy that I bought another switch for my sister's fridge (same as mine). Her light was out too!
Was this helpful?
Thank you for voting!
Refrigerator light would not reliably turn on when the door was opened.
4 of 4 peoplefound this instruction helpful.
William from TUCSON, AZ
Really Easy
Less than 15 mins
Pliers
Switched the refrigerator circuit breaker to off. Put tape around the switch to prevent scratches. Wedged the putty knife into the right side of the switch and pried up.the switch and connector popped out. Removed the connector from the old switch and connected it to the socket in the new switch. Stuffed the new switch and connector back
... Read moreinto its home. Switched on the circuit breaker. Now we have light in the refrigerator with every opening!
Read less
Was this helpful?
Thank you for voting!
Light stopped working
6 of 10 peoplefound this instruction helpful.
Tamara from MONDOVI, WI
Really Easy
Less than 15 mins
Screw drivers
Have had the Sears repairman come to the house to replace this part in 5 minutes for +$100.. twice. When my dad's stopped working, ordered the part and replaced it myself for the cost of the part and shipping. Use a screw driver to pry the right side of the switch and pull out. Best to watch a youtube video first. Takes about 5 minut
... Read morees.
Read less
Was this helpful?
Thank you for voting!
Changing out the Ice Maker tube
9 of 19 peoplefound this instruction helpful.
HARRY from SPARKS, NV
Really Easy
15 - 30 mins
Screw drivers, Wrench (Adjustable)
An easy way to get a refrigerator out from the wall is to use a tow strap or 1/2 to 3/4 in. rope. Throw a loop behind refer while keeping both ends in your hands. Let it settle down to the lower half of unit and pull using both hands. Comes right out. Remove lower panel. Unscrew water valve from cabinet. Remove all tube holders L
... Read moreay some rags down to catch a little water drainage. Turn off water supply valve at wall. Unplug Power. Remove filter and filter holder. (one screw). remove tube from valve by removing plastic C clip. Push plastic ring towards the valve and pull out tube at same time. With the tube free, remove filter, then mount screw to remove the inside filter holder. When it is out, pull the tube doing the same process as the lower end. Pull tube out and replace with new one putting everything back in reverse order. Before placing tube holders back on, turn on water to check for leaks. After turning water back on and plugging in power, push refer back into place. While I was there, I also replaced the hose from the wall to the refer.
My Orders
