68EA3CW (10) Magic Chef Range - Instructions

Once oven was removed from wall not to bad

I ordered the 2 burners that were not working. When I got the burners, I discovered that one of the burners was still working and the wiring under that on had burned out. So I ordered the little box kit and repaired it. I only needed to strip wires and twist together and replace the small box. Now all are working and I am cooking with ... Read more all four burners again. All for about $50.

Pug it in! That's it!

removed old and installed new

My son-in-law installed the new element. First turn off the electricity and remove oven door. Then unscrew all connections to the element.The back electrical wires come out from the top back oven. The bracket screw faces the oven and the electrical wires are so short there is very little room for a screw driver (get the shortest one you c ... Read more an find..abt as big as your thumb if possible).Once that was out the element came out with no problems.Then it's just reversing the step. Again, that back electical bracket is difficult to get to for install. Also, the new screws in our kit were Philips, but the old ones were flat so check those out before turning off the oven light.

I was unable to remove the screw which held the electrical element.. so I took the new surface burner receptacle and removed the metal part, and used the old one and put in the new one in the old metal part and rewired, and it is like new.. now I need to do another one.

Range is a 1967 model Maytag. First I removed drawer under oven, unplugged the range and pulled it out from the wall. Removed oven door by positioning it in the partly-open detent position, then pulled up to remove the door. Next I removed 7 screws per side panel: 3 in front and 3 in back, and one on top under cooktop, which retains the c ... Read more ooktop hold-down clip. With side panels removed, I noted the oven door spring position on the intact left side, then replaced the right-side spring first using the same spring adjustment positions. As I replaced the spring, I applied lithium grease to the spring hook pivot points as well as the spring coils where they rub against the interior wall. I repeated the process on the left side. I reassembled the side panels, oiled the door hinges and reinstalled the oven door. Reinstalled range and bottom drawer. The oven door operates like new, and the new springs are totally quiet — good for another 47 years!

used drill to remove old screw

The Burner Control Switch - 250V Part Number: PS2089409 that this site recommended was the right part for this older range. Had to remove screws to pull out the front panel with knobs, but it only pulls out a couple inches due to wires so it is tight to remove old switch. The five tabs are not in same spot so go by the labels and the wi ... Read more re lugs fit just fine, and the knob snapped right on and works great. Thank You!

The repair itself is really quite easy. Cut the wires, strip the ends and attach the new receptacle with wire nuts. The hard part was getting to it. My cooktop is about 30 years old, so I had to wade through piles of nasty built up grease. Some of the sheet metal screws were unworkable, so I had to cut them off with a Dremel tool. Not ... Read more a pretty picture, but that's how repair work is on old stuff.

Starting by me making a substitute prong to keep the stove working while the part this coming by mail. was a piece of cake.

new drip bowl fit perfectly and was a snap to install.

Just pull the old out from the stove and put new one on the stove and then tested the burner that is working fine. Thank you very much for order the part. Have a great day.

Just plugged it in and away I went.

The element appeared to have been damaged. I replaced the element with ease. However, I still have the same problem. The oven does not heat up to the set temperature. Information from the part select website is that it is more likely the long oven sensor. I ordered one and will provide the results after I have this sensor replaced wi ... Read more th a new one.