66578009801 Kenmore Range - Instructions

Removed stove from slot in wall. Bent rear left leg would not unscrew due to bent metal bracket. Used hacksaw to cut out leg, then straightened metal bracket with small hammer and was able to screw new leg in and adjust height by using level on stove before reinserting stove its slot. Recheck level after pushing back in place and adju ... Read more st front legs if necessary. If not for bent metal receiving bracket, would have taken much less time. Still easy tho. R'cvd part in two days. Very quick.

Easy just loosened screws took apart door, removed broken glass and installed new glass.It took longer to clean the stove! Lol!

removing the screws holding the burner together was impossible. they snapped off and I had to drill them out. that took the most time. after that it was 100% easy hookup. clean up of the burner was done with a wire brush. good quality products. thanks.

I had to use a dremel to grind the heads off the rusted in screws that hold the burners to the stove top then drill out the screws and use larger sheet metal screws to reassemble. Don't lift the stove top much with the burners attached or you'll bend the gas lines. Two screws inside the top oven hold the top down. Without the rusted sc ... Read more rews it would be an easy job.

removed oven door, unscrewed 2 screws on front of plate covering burner at bottom of oven. Undid wing nuts on tent-like cover, unscrewed 2 screws at back of burner (igniter "hiding" under left back side). Pulled oven away from wall (yuch, where did that stuff come from?), unscrewed 2 screws of bottom plate, undid connector to old ignit ... Read more er, fished wires with connector from new igniter, plugged them in. Attached new igniter to bottom of burner, rescrewed. Put all screws and parts back in correct places. Cleaned oven door before putting it back on. Turned oven on........baked bread!! Hooray! Repair was easy-peasy!

It was necessary to take the decorative glass and metal safety panel off using a screwdriver in order to get to the frame that holds the safety glass. It was hard to slide the new glass into the frame without help from a second person to hold the other pane in place.This was an easy repair to make I would just suggest having 2 people to ... Read more hole things in place while replacing screws.

My first suggestion, after turning off the power to the unit, is to take the oven door off. Two simple screws and it's off! It makes getting to the temperature sensor much easier. I also moved the oven out so I could get access to the back to remove the rear panel. The ordered part came with two pigtails, neither of which fit my oven ... Read more wiring harness. I cut one of them and the wiring from the faulty sensor, spliced them together with wire nuts and made my own connection harness. The new sensor went in with little effort. The wiring went together flawlessly with the spliced connection protected between the oven cavity and rear panel. Reattached the rear panel and the oven door, then slid the oven back into place. Turned on the electricity and back to normal! Problem resolved!!

Followed instructions I found online at the Maytag site.

Undid screws on front and some on the back and replaced part and put screws back on and it fixed the proble

I had to pull the range out from the wall and loosen the rear cover to free the connector for the sensor as it got stuck on a corner guide. Put the new sensor in, rear cover back on, range back in place and tested the oven. Oven heats fast now and keeps a more even temp. Makes me wonder how long I was trying to cook with a bad sensor.

First, I called Sears who wanted $440.00 to send a tech out to repair the stove. Second, I visited various web sites to find out what the problem was. I watched a brief video on Part Select which showed the repair of the stove. I then checked other parts stores on the web and selected Part Select based on price and video. Installation was ... Read more very easy just as the video showed. Stove was repaired in less than 30 minutes.

I lifted the burner tray from stove turned it upside down then removed six small screws from side of cover pan then I removed the cover then I removed the screws from the back of the old burners and igniter.Then I turned the old burner counter clockwise and it lifted out easly. the igniter is removed with no problem. The new burner is ... Read more put in place and turned clockwise to lock in place.Then replace then the gas tubes and igniter and igniter wire then put tray cover on.

Ordered the oven sensor. Two screws to remove to replace old sensor. Since this was a slide in unit, you had direct access to the wiring harness. Used the adaptor. Total repair time about 20 minutes. A very easy do-it-yourself project.

Slide oven door off hinges. Remove old gasket. Instal new gasket. Used eraser end of pencil to help feed in ends of gasket into respective holes for excess. Note: job could have been accomplished without taking off door but I wanted to take door appart to clean inside and out of glass.

Cut off the electricity at the junction box. Removed two screws from the sensor at the back of the oven. Then pulled the sensor with the wire out of the installation hole in the back of the oven. Disconnected the quick connect plug from the sensor and reconnected the new part. Reversed the process and screwed the two screens back into ... Read more the oven wall. Turned the electricity back on and started up the oven. (Everything ran well for about three days when the oven again signaled "F-5" indicating the oven was again not functioning properly. Restarted the oven and is currently running properly. My spouse does a lot of baking with this oven for cookies, roasts, etc. Next time it fails I will be forced to call a repairman as I believe there is something wrong other then the heat sensor.