66575776890 Kenmore Range - Instructions

I numbered every part. ex: 1 L., for first part removed left side. I used a magic marker to circle the holes and wrote the number of screws used on the part, set the srews in a separete place, so that I new where these screws went to. The cleanup was pretty time consuming, but I was able to keep my stove, when every repairman I called to ... Read more fix my stove told me I was better off buying a new stove. ($600.00 stove 2 years old)Please Note: The insulation blanket needed for the entire stove is two pieces, the sides and top are one part # and the bottom and back, are another part #. I did not know this. I just purchased the top and sides. I got lucky, the back and bottom were still in good shape. So I guess I should have read the description of the part more carefully to see what it covers, before I ordered it. It took two people two hours to do the work, it was really nice to have an extra set of eyes, to remember what direction pieces of metal from the stove went. I would do it all over in a heart beat instead of buying a new stove.

My husband pulled out the stove turned the gas off then he pulled out the part and replaced igniter....it took only about 20 min to do this job it was very easy and prior to us doing ourselves i called a well known company that does home repairs, I also called a few smaller businesses and to replace this part was anywhere from $175- 250 i ... Read more f not more. we are very very happy with our decision to replace the part ourselves unstead of spending extra money we didnt have .

I pulled the range from the wall and disconnected the power cord. I removed the grates, burner caps and the burners from the cooktop. Using a plastic putty knife, on either side of the range in the front I pushed the retaining clips to allow the cooktop to be raised. I used a short board to keep the cooktop open. I cut the wire leading to ... Read more the broken igniter and removed the old igniter. I put the new ignitor in the mounting hole. The igniter wire connects to the spark module which is in the back of the range. To access the module I removed three top screws on the backplate(you have to get behind the range) and removed the top access panel. I used the old wire to pull the new wire through to the module. I disconnected the old wire from the module and connected the new one.

Reassembly was easy. I replaced the backplate and screws, lowered the cooktop, replaced the burners, caps and grates. I plugged the power cord back in and slid the range back.

well had I known that the trim did not go over the glass, the project would have been easy, but I thought the trim held the glass in, but that was not the case. After much juggling discovered that the trim went under the glass, and at that point the instilation was very easy.

After reading many forums found that this error happens when trying to clean the oven and there is a failure in the latch motor to lock the oven door. It was suggested 1st to just tunr the breaker off to the over wait and then turn it back on to see if the error would clear by itself. If not then you'll have to do what I did and buy a n ... Read more ew Latch Motor and replace it. Fairly easy to do:
) Move oven to get to the back panel
) Disconnect oven from power
) Remove the 8 screws to get the back panel off
) REmove the Latch motor screws (2) and remove the motor after twisting to get the latch rod off
) Put in new latch motor by 1st putting the latch rod in the motor assembly
) Screw the new motor in place
) Replace back panel
) Power on Oven
DONE!

Socket Lite come with clips attached to the outside
of the housing. After you unhook the 3 lead wires
that are attached to the unit. All you have to do is push in on the clips and release the unit. Then you
snap in the new unit. Attach the 3 wire leads, put a
oven bulb in the socket end, and the install the light cove ... Read more r

Broken ignitor wire had been previously removed to determine part number. Exact length was not availible (37"), but similiar unit (36") (one inch shorter) worked with zero problems. To re-install replacement wire/ignitor, I removed all four grates, and surface burners (allows top surface to pivot upwards.) Raised front of stove top surfac ... Read more e by pushing in side, hold-down clips, using butter knife. Propped up surface with board. Insert clip end of igniter lead through hole in top surface and led wire back and towards passage to rear plug-in terminal location. Removed upper, rear sheet metal cover plate (must pull entire range away from wall.) Fed thin/ some-what-stiff safety wire down through plastic protection sleeve (all four ignitor wires go through the sleeve.) Wrapped wire around clip on end of igniter lead, pulled igniter wire up through plastic protector sleeve, disconnected pull through wire, and pushed connector clip on ignitor wire into ignitor terminal block. The rest was nothing more than screwing things back together in reverse order.

screwed in the new glide by taking out old broken one and screwing in new one. wife happy now.

PS733869 Door Trim Kit - Since I was replacing broken and discarded trim parts and had taken the replacements out of their identifying boxes I had some unneccessary difficulty since the parts are not marked. Point to reference is that the 9/16 side of the trim goes on the OUTSIDE EDGE of the door and the glass and handle are attached AFT ... Read more ER the trim is installed. Glass goes OVER the trim and not held in by it, the handle and the lower bracket does that.

I just unscrewed the old one out, which was 2 screws and screwed this one in. But the thing that was best of all was how fast the part came in. It literally came the next day.

Installing the part was really easy. I first turned the gas off, simply remove two screws tht hold the igniter in place. I then remove four screws from the back panel and disconnected the part. The feedback from other users on your site made me realize how easy it was. It took less than thirty minutes.

I had already removed the 2 plates in the bottom of the oven to take an initial look. After not finding anything obvious, and searching on line for advice, I ordered the igniter. After the igniter arrived it was a matter of removing 2 screws, pulling out the lower drawer to gain access to the igniter disconnect, and done.

tha ... Read more nks for getting the correct part to me so quickly. Also the diagram and part number search was right on the money!

We removed the door from oven assembly and laying it flat on the bench removed the stainless steel cover from the rest of the door. Removing the shattered pieces of safety glass was done heating and scraping off vinyl tape.(difficult.)Caution! Do not allow any pieces of glass get under the stainless steel cover, it will leave ugly scratch ... Read more es! We purchased double sided vinyl tape 1/2" wide, 1/16" thick and aluminum "Flue tape" (600 deg. F) 1 1/2" wide from local hardware store to replace the original ones in their previous location. Fitting the new glass on sticky tape has to be done accurately. (no problem). Assembling it was little tricky but still within the ability of a do-it-selfers. We wondered if we should not put the rough side of the glass facing in or out. The original was with the smooth side out so that what we did. If any additional scraping of accumulated grease is needed especially on the inside glass, it requires more disassembly, but we would strongly suggest doing it (we did), while it is all opened. To our surprise the glass arrived by Fed Ex within 24 hours of ordering and now our Whirlpool is gleaming like new again. The cost of this product with shipping/handling by PartsSelect was much lower than ordering it from the other "original" source. Thank you! Sincerely Fred T.

Removed oven from wall unit and took the back off. Removed the old socket assembly by depressing the ears and forcing unit into the oven. The electrical wires were easily removed since they are spade connections and slip off. They also are different sizes so that there is no chance of erroneously putting them back in an incorrect order. ... Read more The new unit simply slips in from the front and snaps into place. The most difficult part of the entire process is removing the old unit. A little "friendly persuasion" is required to get the old unit out.

1st; I opened the door, 2nd; removed the keepers that prevent the door from coming unhinged. 3rd; placed 2 short screws in the holes in the hinges. 4th; raised the door until it stopped. 5th; lifted the door upward and slid the hinges out of the slots in the range. 6th; laid the door face up on a microwave stand. With a handle on the outs ... Read more ide, and hinges sticking out of the inside, it was inpossible to lay the door flat on a larger surface, and get around it. 7th; removed 2 screws from the inside top, and the 8 screws from the very bottom. 8th; removed the bottom rail, and the handle assembly. From there everything was stacked pieces. Picked the glass front up, and carefully set it safely aside. Picked each piece up and cleaned it, and started the re-assembly. The hardest part of the process was getting the fiberglass rope around the inside glass, to stay in place during the initial re-assembly. From there, the assembly was just the reverse order. the process was about 1 hour and 20 minutes, due to lack instructions and practice, plus cleaning, finding screws, and tools, Instructions may have been on line, but I didn't find them. The new hinges came with pins in place, and should have come with an extra set to lock the old hinges.