6657342702 Kenmore Trash Compactor - Parts

This is the drive gear kit for the ram that compacts the trash inside your compactor. If your compactor ram is getting stuck, there is excess noise during its cycle, or if your compactor does not stop at the end of its cycle, the driving gear may be the issue. The gear is white, plastic and approximately 4.5 inches in diameter. This drive...Read more gear kit includes both gears, pin spring, retaining clip (c-ring), ram stop, ram cam, and instructions. Make sure to disconnect the power to your trash compactor before beginning the repair.

The front facing foot is sold individually. It is used on your washing machine and can also be known as an adjustable leveling leg. This specific front facing leveling leg has a rubber foot. It is important that when installing this part you are very careful, if not installed correctly your washer will be off balance which will then cause...Read more it to vibrate and/or shake during the cycle. The function of the adjustable foot is to keep your washing machine supported and to make sure that it is level at all times. The tools you will need for this repair include a pair of channel lock pliers, and a 9/16 wrench.

The rotary switch kit is also known as the start switch or the on and off switch, and is used to power on your trash compactor. The function of the rotary switch kit is to control the electrical power that is going into your trash compactor. This process happens when the switch sendsvoltage to the motor to start the compacting cycle. If y...Read moreour switch is broken the trash compactor will not start. A multimeter test can be performed to test the switch for continuity. The rotary switch kit will come with an on and off rotary switch, and two chrome knobs.

This bearing roller may also be known as the wheel assembly or the container roller bearing, and it is a piece for your trash bin. The function of this bearing is to work in conjunction with your trash bin to allow the canister to roll free. For this repair you will need a nut driver, a pair of pliers, a screwdriver set, and an adjustable...Read more wrench. The most obvious symptom that will require you to replace this part is if your drawer is hard to open and/or close. Your appliance comes with two bearing rollers and it is sold individually.

This wheel assembly, or roller assembly, is for a trash compactor. The kit includes two wheels that are approximately 1 inch in diameter each. The wheels allow the trash compactor container to roll in and out of the appliance. You may have to replace the wheel assembly if the container does not roll smoothly. To access the existing wheel ...Read morekit on your appliance, uninstall appliance from the cabinet, depress foot petal to lift the container off its track, and remove the container from the tracks. This kit is an OEM part sourced from the authentic manufacturer factory.

This replacement knob and safety key is designed for trash compactors, providing both convenient operation and added protection. It functions as the start control, allowing you to easily activate the compactor, while also serving as a built-in safety feature—removing the key disables the unit to help prevent unintended use. Durable and ea...Read moresy to install, it’s an ideal solution for replacing worn, damaged, or missing knobs, helping restore safe and reliable everyday operation.

Sold individually. The size of this screw is 1/4" hex head and 10-12 x 1/2".

This drive motor is for trash compactors. The drive motor turns the gears and chain that raise and lower the compactor ram. If your trash compactor will not start or will not stay on during the compaction cycle, you may have a defective drive motor. The start or run switch is used to supply power to the motor to initiate the compaction cy...Read morecle. If the windings in the motor are open or if the motor centrifugal switch is open, the unit will not start. To check for a defective motor, you will need to remove the unit from the cabinets and disconnect the power.

This screw is sold individually. Size: 8-32 x 1/4 inch.

This nut is a genuine OEM part for a variety of trash compactors. Made of high-quality metal, the flat side of this washer faces and is fastened to the side of your trash compactor to secure the railing system to the main drawer of the compactor.

This screw is sold individually. It is a genuine OEM replacement part, and it is designed for use with refrigerators. Most often it is used with the ice bucket ice deflector, retainer clip, and front cover. Due to varied uses we recommend referring to model-specific diagrams for exact placement. This screw measures 8-18 by 1/2 inch.

Sold individually.