6654428997 Kenmore Range - Instructions

After removing the back of the stove, the old light socket was fairly easy to remove. The new socket slipped in place and the wires reattached and now the oven has a light again. A very simple process--especially for someone who's not an expert in repairing appliances.

Removed the two Philips head screws that attach the element to the back wall of the oven. Pulled off the two wire terminals from the spades on the back of the element. Pushed the two wire terminals onto the spades on the back of the new element. Noticed that one was not tight, so disconnected, squeezed down the wire terminal, and reco ... Read more nnected. Inserted the two screws that attach the element to the back wall of the oven. Element works fine.

Turn Off Breaker.

Removed oven racks....

Removed two screws holding element in place...

Disconnect spade lug connectors from old heating element.

Connected spade lug connectors to new heating element.

Reinstall 2 screws holding element.....

Replace oven racks.

T ... Read more urn Breakers back On.

Done 10 Min. Install

This is an easy fix. Just before the holidays, it was imperative that this appliance be in top shape. Since the door 'hung' wrong, it was determined that the hinge pin broke. Remove the 2 phillips head screws on the door and open the door to the to a 15 degree opening. This position allows you to slip the door off the hinge levers. N ... Read more ow that the door is off, replace the hinge pin and slip the retainer ring on with a screw driver blade to push it on the pin. Slide the door back on the levers and fasten the retainer screws. DONE!

Purchased 2 piece broiler pan from this site

1. Open door and place a nail in the small circle in each of the two side hinges. This step is crucial. It keeps the hinges from springing back into the oven when the door is removed.

2. Remove the 2 screws on the oven door at the top of each spring. Close the door until stopped by the 2 nails, then lift the door up and off the ... Read more hinges.

3. Lay the door on a soft surface(some oven parts may be greasy), inside of the door face up, and remove the 5 screws holding the main two halves of the door together. Remove the top piece.

4. Remove the 4 screws that are under the insulation strips. This will damage the strips, but there is no other way. Just try to keep as much of the strip as you can.

5. Continue removing screws and layers of glass (ours had 3 inner layers)until you reach the inner most piece.

6. Replace the broken glass and then reverse the process to put everything back together.

Notes: We work slowly and methodically, so the whole process took us over an hour but we also took this opportunity to really clean every crack and crevasse that is normally hidden. All in all this was not a very hard job and worth doing it as a DYI project instead of calling a repair person.

My husband wanted me to call a repair man but I had read online how easy it was. I received my element in one day from Fresno, CA and followed the instructions given by others on line. I couldn't believe how easy it was. The most difficult was removing the connectors because they were stuck. I used needle nose pliers as someone sugges ... Read more ted. Saved the cost of a repair man.

First tried to replace the glass and gasket without removing the oven door. Removed all screws and took the door apart. However, I found it was very hard to get the gasket to stay in place and put the glass window in place with the door frame still attached to the oven and upright. Decided to go ahead and lift the door off the hinges b ... Read more y removing the two final screws. Then the door could be layed flat on the floor and it was much easier to put in the insulation and glass pane.

The honeycomb filter in the vent was missing so I bought the entire vent cap.. Thought it attach with 2 screws from inside the oven.. BUT -- when you loosen the screws, it wouldn't drop.. Looked at the new part and saw that it attaches to the vent outside the oven as well.. So to replace this puppy, you have to pull the cabinet apart.. ... Read more r />
Left it for another day.. Hopefully no grease fires..

Read less