66514423N511 Kenmore Dishwasher - Instructions

I pulled the unit away from the cabinet, unplugged the washer and water line(not long enough to reach) removed two nuts from the underside and replaced the heating unit.

The repair was easy. Getting the unit to slide out from under the counter was more time consuming.
After water and power is disconnected, tip the unit over onto one side to gain access to bottom. Look for two white composite plastic posts (insulators) about 2" long each with a single wire inside. Remove the two wire connectors then ... Read more unscrew the insulators from the old heating element using an adjustable wrench. Inside the box remove the two metal element supports and pull out the old element. Clean and dry the area in and around the openings where the new element will be re-inserted. Carefully place the new element into the holes with the included new rubber washers. Re-install the two metal element supports on the inside of box. On the bottom, re-install the two insulators to the ends of the element, do not to tighten too much to avoid over compressing the rubber washers which could cause premature cracking. Reconnect both wires and check continuity from the door mircro-switch (white-violet) lead to the (white-red) lead on Electronic Controller connector #1 (P6). The circuit thru the element should be good if the Multimeter reads 10-35 ohms. Put the unit securely back under the counter and run a test wash. Works fine now.
I do recommend, if don't know how to use a multimeter or are concerned about accessing the electronic control box; contact a professional.

I turned off the power to the dishwasher, removed the kick plate, raised the front levelers, disconnected the electric to the appliance, turned off the water supply to the appliance, disconnected the water supply, disconnected the drain system from the garbage disposal, unscrew the appliance from the countertop, then I remove the applia ... Read more nce from underneath the counter. I then tilted the appliance back and then in screwed the plastic retainers that held the heater element in place, removed the old one, replaced it with the new one in reversed the whole process

After bailing out the unit, filled filter hole with a moderate amount of Dawn dish washing detergent. Ran dishwasher twice to remove all Dawn from the unit. Had to bailout the water (and suds) from the washer both times. After the dishwasher finally drained I inserted the new filter..

Looked at other side of top rack which still had the stop. Just had to orient the direction of the stop and push it firmly onto the rack arm. Took a couple tries, but it went in and locked. Works perfectly. Inexpensive and easy fix to to very annoying problem.

I unscrewed the dishwasher from the counter (two screws under the countertop), and pulled it out about a foot so I could access the friction sleeve. I used a needle nosed pliers to slip a spring latch off the door. Then I slipped the new friction sleeve on and reattached the spring. Tested the door. Success! Super easy. About 5 minutes of ... Read more work.

placed sprayer arm in position and twisted it into position, about a 1/4 turn, snaps into place. total of 15 seconds!

repair went smooth for the grommet. suggest a small of vasoline to ease installation of grommet

I did not relize that the drain hose was in two parts. Naturally I ordered the wrong half. So after I relized my mistake, I re-ordered the correct part. Once the correct part was received the repair was easy and went well.

put new hose on, very easy.

The water valve float lever was broke. So I replaced that and the water level switch. Probably didn’t have to replace switch. Very easy!!

Installed new pump from the front. Power off remove front cover reached my hand behind pump for release clip, push down turned counter clockwise pump comes out. Disconnected electrical plug attached plug to new pump. Put pump in at 45 degrees rotated clockwise until hear clip lock in . Tested then replaced cover

The top and bottom parts of the lower wash arm were separating. This caused water to spray out the ends of the wash arm and come out the front of the dishwasher. In addition this water was not spraying upward resulting in dishes not getting cleaned. Took me a while to figure this out but the repair was simple.

You only need to pull it out about 6 to 8 inches and you don’t need to disconnect anything to slide it on

Took out old rack by twisting the rack supports. Used old supports because in good shape. Removed the wand from old rack and placed on new rack. Then replaced the supports. Worked great.