66213293K112 Kenmore Dishwasher - Parts

This rack adjuster kit (Dishrack Adjuster Kit, Adjuster Kit, Dishwasher Rack Adjuster) will adjust the height of the upper rack of your dishwasher. It connects to the dishrack. The kit is constructed of grey plastic and metal, and measures approximately 12 inches wide and 6.5 inches tall. The rack adjuster can break from material fatigue...Read more or prolonged high temperature exposure. High temperature exposure can compromise the integrity of the materials. If the rack adjuster breaks, your upper rack may fall down, may be unlevel, or the door may not close. This kit includes the parts to replace the left and right-side rack adjusters and has been upgraded to a more durable metal design (2 adjuster assemblies, 1 left hand and 1 right hand actuator cover, 2 gray adjuster covers, and 2 gray adjuster housings)

This manufacturer-approved Rack Stop Clip is a gray plastic part which can be installed with a screwdriver. Measuring slightly over an inch in length, it prevents the rack from sliding too far and falling off. If broken or damaged, then the rack will slide too far and this is a sign the part should be replaced. It attaches to the end of t...Read morehe top dishwasher rack. This clip can be used for the left or right side, and is sold individually. It is a good idea to replace both sides at once. To make this repair, start by pulling out the rack, then, using your screwdriver, reach in behind the rack stops and press the clips in. You should be able to remove the stops from the track from here. Next, you should be able to slide the track back over the rollers and snap the new track stop into place.

Also known as rack adjuster. Sold individually. This is an original part from KitchenAid, Kenmore, Whirlpool, Jenn-Air, and Maytag for use with Dishwashers. The dishrack adjuster arm positioner clip holds the adjuster arm in the right position on the dishrack. The most common reason for replacing the strap is if the rack will not stay i...Read moren its desired position. This part is sold individually. There are no tools needed to replace the positioner.

This dishwasher drawer track, also known as a rack slider bar, is a genuine replacement component designed to support the upper dish rack and allow smooth sliding in and out of the dishwasher cavity. Constructed from durable materials, it ensures proper alignment and stability of the rack during loading and unloading. Over time, the track...Read more may become warped or damaged, leading to issues such as rack misalignment, jamming, or wheel detachment. Replacement is recommended when the rack no longer slides smoothly or shows signs of wear. Installation requires a flat blade screwdriver to remove the rear stop and access the track. Always disconnect power before servicing and verify model compatibility prior to purchase.

Designed to support flexible loading, this dishrack adjuster helps raise or lower the top rack in your dishwasher. A damaged or missing clip can cause the rack to become unstable or difficult to adjust. Replacing the adjuster ensures the rack stays securely in place and functions as intended. This is a genuine replacement part and is sold individually—check your model to determine how many are needed.

Enhance the efficiency of your Whirlpool dishwasher with this top-quality spray arm. This essential part rotates and sprays water effectively to clean the dishes inside the dishwasher tub, providing a thorough and comprehensive cleaning. Durably constructed, it stands up to regular use and ensures a lasting performance. Keep in mind, it's...Read more advised to wear work gloves in order to protect your hands while handling the repair. Invest in this Whirlpool spray arm for an unmatched cleanliness standard.

The adjuster cover goes on the outside of the adjuster housing. It is used to support the height adjuster and also protects the internal components of the adjuster housing.

Sold individually.

Sold individually.

The upper spray arm rotates and sprays water to clean the dishes inside the dishwasher tub. If your dishes are not being cleaned properly, you should check if there is an issue with the spray arm. To check your spray arm, make sure the spray arms can move evenly and freely on their bearing rings and mounting brackets. Remove your spray ar...Read morem and check to ensure they are straight and undamaged. This spray arm is made of high-quality plastic and is just over 5 inches long.

This OEM dishrack guard clip fits on the front of the upper dishrack and acts as a bumper between the rack and inner door panel. This guard clip is approximately 3 inches long and made of plastic. To replace this part, open the dishwasher door and then slide the upper dishrack out, then simply unclip the faulty guard clip before fastening the new one.

This upper dishrack assembly is designed to hold dishes, cups, and bowls securely in the top section of your dishwasher during the wash cycle. It provides stable support and helps optimize cleaning performance. While the rack itself is included, rollers, slides, and other hardware must be transferred from your existing dishrack. Replacing...Read more a worn or damaged rack can improve loading stability, ensure smooth sliding, and restore proper dish positioning.