65022 - Parts

This micro-switch is designed for use in your microwave. The function of this part is to monitor the door latch position and communicate to the electronic control board whether the latch is open or closed. If your microwave does not provide heat, or will not start properly, you may need to replace the micro-switch. This part is approximat...Read moreely 1 inch in length and 3/4-inch in width. It is made of black plastic with two metal prongs. This is an OEM part sourced directly from the manufacturer. This part is sold individually. Be sure to disconnect the microwave from the power source before you begin this repair.

The door switch, often referred to as a primary interlock switch, provides power to the various components in the microwave when the door is in a closed position, and interrupts power when the door is open. This door switch is approximately 1 1/2 inches long, and has 2 metal prongs called terminals that extend from its body. Common sympto...Read morems related to a faulty primary door switch include: microwave will not turn/shut off, or the microwave will not heat properly. You can check the switch for continuity using a multi-meter. With the actuator button depressed, you should see continuity between these terminals. If there is no continuity the switch will need to be replaced. NOTE: Before you begin this repair, first make sure your microwave is unplugged, and that your capacitor is discharged. A capacitor stores large amounts of electricity even when your microwave is unplugged.

The fuse-time delay may also be known as a line fuse or a microwave fuse, and it is a piece for your microwave. The function of this part is to shut off the microwave if there is a power surge, in order to protect your microwave from damage. You should consider having a service technician install this part as the high-voltage capacitors i...Read moren a microwave can contain a very harmful electrical charge, even when the microwave is unplugged and has been inactive for some time. The tools that would be needed to complete this installation include a Phillips screwdriver, an insulated screwdriver, and a pair of pliers.

This magnetron in your microwave creates the radiation needed for cooking or warming your food. It is located inside the main cavity, typically near the transformer or waveguide. When the magnetron becomes defective, your food may not heat up properly or heat up at all. Additionally, buzzing or humming sounds may be noticeable while the m...Read moreicrowave is in operation. With a malfunctioning magnetron, your microwave loses its primary function. To remove it, you first need to unplug your microwave from its outlet. Before touching any components, discharge the capacitor by placing a screwdriver, with an insulated handle, across the two terminals of the capacitor. Once the capacitor is discharged, replace the current magnetron by disconnecting it from any wires and removing any mounting screws or clips. This magnetron is sold individually and is supplied directly from the original equipment manufacturer.

This is a genuine Husqvarna replacement part, sold individually. Wheel 532401274 attaches to each side of the mower deck and propels the lawn mower. A wrench is required for replacement of this part. This part is compatible with the Husqvarna lawn mower models that are listed below.

This blade is sourced directly from the manufacturer for use in Craftsman and Husqvarna lawn mowers. The blade is the part of the mower that is responsible for cutting and mulching the grass. It is 22" long, made of black metal, is not part of a kit or assembly, and is sold individually. If you hit a hard object, you may bend the blade,...Read more causing a vibration. You may also have problems with the grass being cut as the blade dulls over time. If the blade is bent, damaged, or worn, it needs to be replaced. You will need a socket set to complete this repair. Customers rate this repair as Easy.

The Dust Shield is a 6-3/4 inch, black plastic part, used to prevent dust or debris fouling the wheel or axle. It attaches inside of the wheel around the axle. Installation is rated as "Easy" and will require a wrench. If broken, damaged, or worn due to fatigue, you will see visable damage and you may have debris getting caught in the axl...Read moree. If broken, replace it. Refer to your make, model and diagram to make sure you're choosing the right part. This part comes individually sold.