EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

6479237320 Kenmore Range - Instructions

All Instructions for the 6479237320
1 - 15 of 22

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
There was no heat on the coils.
48 of 52 people found this instruction helpful.
  • Shaohui from East Lansing, MI
  • Easy
  • 15 - 30 mins
  • Pliers
I opened the lid, and found that the terminal blocks were burnt, the wires were melted. I ordered one set of terminal block to replace the burnt one, and it worked. Before I started, I shut off the electricity in the whole house to be safe.
Was this helpful?
Thank you for voting!
Surface burner coil did not work.
23 of 33 people found this instruction helpful.
  • Gregory from Mont Belvieu, TX
  • Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers, Socket set
TURN OFF ALL POWER TO KITCHEN. Took off all burner coils and plates below them. Lift hood. Locate part. Remove old part and replace with new part in same way as was previously installed. The wire that comes with the kit is actually too much wire, but just arrange it the best you can and leave it....no big deal. I didn't have a magnet , but needed one. The wire from burner coil to switch runs through a harness which is screwed on to the body of the oven (below the range). Be careful NOT to drop it behind oven when taking it out. I dropped it and took forever to get it. That turned a 20 minuate job into an hour and a half. Otherwise this is an easy job that anyone can do. Refrigerator compressor is next. Have fun.
Was this helpful?
Thank you for voting!
Could not find the correct replacements (burners & drip pans)
13 of 21 people found this instruction helpful.
  • Barbara from JEFFERSON, GA
  • Very Easy
  • Less than 15 mins
After months of buying the wrong parts & cost I discovered this site So easy to order & quick delivery, plus very easy installation. Thank you. I also wanted to add that the reps (Tanisha & Matthew) were extremely helpful & informative. I can only hope all the reps equal their performance. I will definitely be using this site, before an y other source. Knowledge & cost is also important to me & that need was met. Good job!
Was this helpful?
Thank you for voting!
Have tried 3 different store-bought drip pan sets over the past year. None of them laid flat.
10 of 25 people found this instruction helpful.
  • Jennifer from Saginaw, MI
  • Really Easy
  • Less than 15 mins
Simple installation of new pans and all are level! Thank heaven! Thank you, PartSelect!
Was this helpful?
Thank you for voting!
A tenant left the Drip Bowls in an uncleanable state. I could not find a suitable replacement..
3 of 4 people found this instruction helpful.
  • Larry from SACRAMENTO, CA
  • Very Easy
  • Less than 15 mins
Most trainable people can pull out the heating elements and replace the Drip Bowls. The great thing about the ordered drip bowls was that they FIT! Most drip bowls sold as easy replacements for GE or Hotpoint appliances do not fit and wobble the heating element or drip bowls. If not fitting correctly, the tenant usually destroys the he ating element and the drip bowl.
Was this helpful?
Thank you for voting!
Drip pan was ruined by renter
1 person found this instruction helpful.
  • Karilyn from KEWADIN, MI
  • Very Easy
  • Less than 15 mins
I ordered a new drip pan. Piece of cake. Stove looks new again.
Was this helpful?
Thank you for voting!
Needed new drip bowl, was very hard to find one that fit my stove
1 person found this instruction helpful.
  • Rosemary from BROOKFIELD, CT
  • Very Easy
  • Less than 15 mins
Installed easily, was most impressed with the speed of delivery and it was the perfect size!!
Was this helpful?
Thank you for voting!
the drip bowls were worn out
1 person found this instruction helpful.
  • linda from STANTON, MI
  • Very Easy
  • Less than 15 mins
simply replaced them.
Was this helpful?
Thank you for voting!
Drip bowl from a big box store was too big even though both say 8”.
1 person found this instruction helpful.
  • Kathleen from INCLINE VLG, NV
  • Very Easy
  • Less than 15 mins
Ordered the part and set it in.
Was this helpful?
Thank you for voting!
Old Terminal Block was arcing.
1 person found this instruction helpful.
  • Robert from HOUSTON, TX
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
Cut Wires to old terminal block and wired in new Terminal Block
Was this helpful?
Thank you for voting!
Live in an apartment and they had generic drip pans on the stove causing pots to tilt when cooking.
0 of 1 people found this instruction helpful.
  • Jennifer from Cleveland, OH
  • Really Easy
  • Less than 15 mins
Replaced drip pans that the apartment Superintendent had in place with the correct drip pans and now cooking is beautiful again! No more uneven cooking on the stove top.
Was this helpful?
Thank you for voting!
Finish coming off of bowls
0 of 2 people found this instruction helpful.
  • Robert from Ledyard, CT
  • Really Easy
  • Less than 15 mins
Removed burner from each one. removed drip bowl. Inserted new bowl. Replaced burner. Excellent help from order people so I got the correct bowl was irreplacable.
Was this helpful?
Thank you for voting!
Burners would not lay flat
8 of 36 people found this instruction helpful.
  • Alfred from Forest, VA
  • Really Easy
  • Less than 15 mins
Removed the burner elements, removed and disposed of old drip pans, cleaned the area, relaced with new drip pans and replaced the burner elements. Verified all burners were level - good as the day it was new!
Was this helpful?
Thank you for voting!
Right Front [surface burner terminal block kit]
  • Wayne from Montoursville, PA
  • Really Easy
  • Less than 15 mins
  • Nutdriver, Screw drivers
We did the repair by following the inclosed instructions. we are elderly retired average ages 82. This was our first repair and it went very well. We are so pleased to have saved over $80.00 compared with hired labor 3 yre. ago for the same part. Thanks so much for your good service.
Was this helpful?
Thank you for voting!
Drawer guide
  • Lee from Grass Valley, CA
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Used Phillips screw driver, installed guide, applied lubricant.
Was this helpful?
Thank you for voting!
All Instructions for the 6479237320
1 - 15 of 22