64050439 General Electric Dryer - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
sqeekysqueeky rear drum bearing
1 person
found this instruction helpful.
-
mitchell from Warren, NJ
- Easy
- More than 2 hours
-
Nutdriver, Screw drivers, Socket set
Open top by removing 4 phillips head screws above opened door, pop top up. Remove rear access panel, remove belt from drive & tension pully. Loosen top front screws, remove front panel to gain access to remove drum. After drum removed, I realized why rear bearing went bad- two front guides were worn causing rear bearing to angle and wear
... Read more
out. Replaced front pads, buttoned her up and now quite as new. Also replaced drive belt while in there.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
rear dryer bearing assembly not threaded
2 of 4 people
found this instruction helpful.
-
Frank from Glendive, MT
- A Bit Difficult
- More than 2 hours
-
Nutdriver, Screw drivers, Wrench set
The rear bearing plate had no threads where the screws go to hold it to the back of the dryer drum. I have never bought anything else that needed threads cut in it to be used as a replacement part.
Other Parts Used:
Was this helpful?
Thank you for voting!
Old lint filter had a hole in the screen.
1 person
found this instruction helpful.
-
Dennis from CLOVER, SC
- Very Easy
- Less than 15 mins
Replaced filter
Was this helpful?
Thank you for voting!
Belt Broken that turns the drum
1 person
found this instruction helpful.
-
Wayne from Williamston, MI
- Easy
- 30 - 60 mins
-
Screw drivers, Wrench (Adjustable)
First I shut off the gas and unhooked the gas line. Then opened the door and removed the screws that hold the top down in the front. I then tipped the top back so I could get to the top of the drum. I removed the screws ( 4 ) inside the door opening and slid the felt seal back. Next I put the belt in the drum and feed part out the crack b
... Read more
etween the drum and the dryer frame, being careful not to cut the belt. I woorked the belt around the crack and pulled it toward the drum. When I got the belt through it was all the way around the drum and I just put the belt over the motor pully and pulled the tensioner back and wrapped the belt over it. Put all the screws back in and the back on and fired it up. Works as good as it ever did.
Read less
Was this helpful?
Thank you for voting!
Dryer suddenly start making a rattling noise
1 person
found this instruction helpful.
-
Ricardo from Hicksville, NY
- Really Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
I follow the easy instruction by a user in your web site to reach the problem area and discoverd the drive belt was broken.
As it turned out, the problem was compounded when I discovered also that the Heating element needed replacement.
At this point I decided it was time to let go and got a new dryer, choosing the same brand ... Read more that lasted 25 years: GE
As it turned out, the problem was compounded when I discovered also that the Heating element needed replacement.
At this point I decided it was time to let go and got a new dryer, choosing the same brand ... Read more that lasted 25 years: GE
Read less
Was this helpful?
Thank you for voting!
Noisy Bearing "SWEEKING"
1 person
found this instruction helpful.
-
Russell P. from Dushore, PA
- A Bit Difficult
- 15 - 30 mins
-
Nutdriver, Screw drivers, Socket set
The first thing I did was move the dryer out so I could "unplug it" !
Then I took the 4 philps head screws out that hold down the top of the dryer, then I lifted up the top and moved it off to the side making sure the wires didn't get pulled out.
Then I removed the 2 5/16 cap screws that holds the front panel on and lifted that ... Read more off "Make sure you mark the down were the 2 wires for the door swich go" Like white on pin 1 and yellow on pin 2!!!
The next thing is to slide the drum foward so you can remove the element package then remove the 3 philps screws in the back of the drum make sure you have someone hold the element package there is a sheild between the drum and the element package that may fall that is a watch out you will need to move the element package up so you can work on it there will be wires hooked to this ring so becare full you don't break them off.
remove the element package you will see the bearing kit attached to that.
There are 4 5/16 cap screws that hold the bearing kit to that remove them and then remove the old bearing kit you may find and E Ring holding the old bearing kit in place (this would be found in the older models).
Before you install the new bearing kit take the new self tapping screws and tap the holes in the new bearing kit mounting plates this will make things go faster!!!
Now mount the bearing plate with the 4 holes to the element package there is a tab that needs to be mount in there too so look at the old one when you are taking it off.
Pick up the sheild that fell pick it up have a second person help you hold everything in place while you line up the holes for the front plate to the back of the drum and start your screws.
Now tighten them down check to make sure your belt didn't slide off the tensioner that is next to the motor before you slide the drum back in place if it did take the time to figure out how to get it back on the right way our you will be pulling things apart again.
What I did was spin the Drum by hand to make sure everything was ok. you will know if the belt is off it will not move when you spin the drum by hand.
Now that you made sure the belt is on you can put the front back on there are 2 studs on the bottom that you need to set the frount panel on before you can put the screws back in in it.
Now that you have the fron back on it hook your 2 wires back up to the door switch like you took them off!
Now move your top back over and you will see 2 clips on the back of it that slide into a grove in the back now that you have that in place start putting the screws back in put the middle 2 in first and tighten them down them put the last 2 in.
Now plug it back in if your vent pipe fell off hook it back up as you slide your dryer back in place now try it to make sure everything is working right and you will hear the differance.
Good Luck with your repairs....
Just a quick note this dryer is over 40 years old and still going.
I have replace 6 elements and 1 drive belt since it was bought new now the bearing kit.
Clean it once a year and the vent pipe every 6 months it will last!!!
Then I took the 4 philps head screws out that hold down the top of the dryer, then I lifted up the top and moved it off to the side making sure the wires didn't get pulled out.
Then I removed the 2 5/16 cap screws that holds the front panel on and lifted that ... Read more off "Make sure you mark the down were the 2 wires for the door swich go" Like white on pin 1 and yellow on pin 2!!!
The next thing is to slide the drum foward so you can remove the element package then remove the 3 philps screws in the back of the drum make sure you have someone hold the element package there is a sheild between the drum and the element package that may fall that is a watch out you will need to move the element package up so you can work on it there will be wires hooked to this ring so becare full you don't break them off.
remove the element package you will see the bearing kit attached to that.
There are 4 5/16 cap screws that hold the bearing kit to that remove them and then remove the old bearing kit you may find and E Ring holding the old bearing kit in place (this would be found in the older models).
Before you install the new bearing kit take the new self tapping screws and tap the holes in the new bearing kit mounting plates this will make things go faster!!!
Now mount the bearing plate with the 4 holes to the element package there is a tab that needs to be mount in there too so look at the old one when you are taking it off.
Pick up the sheild that fell pick it up have a second person help you hold everything in place while you line up the holes for the front plate to the back of the drum and start your screws.
Now tighten them down check to make sure your belt didn't slide off the tensioner that is next to the motor before you slide the drum back in place if it did take the time to figure out how to get it back on the right way our you will be pulling things apart again.
What I did was spin the Drum by hand to make sure everything was ok. you will know if the belt is off it will not move when you spin the drum by hand.
Now that you made sure the belt is on you can put the front back on there are 2 studs on the bottom that you need to set the frount panel on before you can put the screws back in in it.
Now that you have the fron back on it hook your 2 wires back up to the door switch like you took them off!
Now move your top back over and you will see 2 clips on the back of it that slide into a grove in the back now that you have that in place start putting the screws back in put the middle 2 in first and tighten them down them put the last 2 in.
Now plug it back in if your vent pipe fell off hook it back up as you slide your dryer back in place now try it to make sure everything is working right and you will hear the differance.
Good Luck with your repairs....
Just a quick note this dryer is over 40 years old and still going.
I have replace 6 elements and 1 drive belt since it was bought new now the bearing kit.
Clean it once a year and the vent pipe every 6 months it will last!!!
Read less
Was this helpful?
Thank you for voting!
dryer not running
1 of 2 people
found this instruction helpful.
-
Robert from Tranquility, NJ
- Easy
- 15 - 30 mins
-
Nutdriver, Socket set
drive belt gone, replaced belt and bearing
Other Parts Used:
Was this helpful?
Thank you for voting!
Noise when dryer spins
2 of 5 people
found this instruction helpful.
-
Kevin from Glenwood, IL
- Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
unknown
25 year old GE dryer started making strange scraping noises when running. This even when there were no items in the appliance. Turning off the gas, and unplugging the power I disassembled the unit to find the nylon drum bushings worn down. Especially the felt like material under them that I think dissipates friction heat. A ... Read more quick order to GD for the parts, 2 days later I had the part installed, and noise was gone.
Kevin J. Reynolds.
25 year old GE dryer started making strange scraping noises when running. This even when there were no items in the appliance. Turning off the gas, and unplugging the power I disassembled the unit to find the nylon drum bushings worn down. Especially the felt like material under them that I think dissipates friction heat. A ... Read more quick order to GD for the parts, 2 days later I had the part installed, and noise was gone.
Kevin J. Reynolds.
Read less
Was this helpful?
Thank you for voting!
Broken Element
1 of 2 people
found this instruction helpful.
-
Glen from cuningham, KY
- A Bit Difficult
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)
We removed the lid to the dryer. The drum had to come out so the back access was removed and the belt taken off. The drum then slid out the front. The dryer had two elements both were broken. The new ones were stretched to the proper length and laced through the ceramic brackets. The new copper leads werre installed and the coils att
... Read more
ached to them. We cleaned the dryer as much as possible and reassembled it. Works like a charm (for now)!
Read less
Was this helpful?
Thank you for voting!
Belt broke
1 of 2 people
found this instruction helpful.
-
Robert from Patchogue, NY
- Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
Removed Front of Machine, removed access panel on back of machine, reassembled after installing belt and cleaning out machine. Pretty Easy, hardest part is getting around the front of the drum.This machine has been going since 1978. 31 years, 2nd replacement belt and thats all, not bad, the washer that was bought at the same time went aro
... Read more
und 6 years ago, havent had the same luck, since then, two machines and the latest one is giving me problems already. They dont make them like they used to.
Read less
Was this helpful?
Thank you for voting!
No problems
1 of 2 people
found this instruction helpful.
-
Leona from Milford, CT
- Really Easy
- Less than 15 mins
I called customer Servioce and they helped me with the corrfect part number
Was this helpful?
Thank you for voting!
Lint Filter had developed holes in the filter
1 of 2 people
found this instruction helpful.
-
Darrell from De Queen, AR
- Really Easy
- Less than 15 mins
Pulled the old filter out of the door of the dryer and then removed the new filter from the shipping box and took the new Lint filter out of the packaging and then slipped the new lint filter into the lint filter holder and started up the dryer and away we went on our happy way. Thanks to all of you guys and gals at PARTS SELECT.
Was this helpful?
Thank you for voting!
The wire mesh on the lint filter separated from the frame and lint was getting inside the dryer.
1 of 2 people
found this instruction helpful.
-
Jill from Little Chute, WI
- Really Easy
- Less than 15 mins
Took the old filter out and inserted the new filter which was a near perfect fit on a 36 year old dryed that is still kicking! Delivery of the part was less than 24 hours after ordering over the phone. Thanks1
Was this helpful?
Thank you for voting!
The lint filter was ripped in multiple locations
1 of 2 people
found this instruction helpful.
-
Dawn from Madison, NJ
- Really Easy
- Less than 15 mins
I just replaced the old filter with the new filter and I wonder why I didn't order a replacement filter sooner.
Was this helpful?
Thank you for voting!
lint filter broke it was over 10 yrs old
1 of 2 people
found this instruction helpful.
-
Judith from Port Saint Lucie, FL
- Really Easy
- Less than 15 mins
place inside of dryer
Was this helpful?
Thank you for voting!