62945765690 Kenmore Range - Instructions

put the new element in the oven pushed wire onto connector on element held it up to match holes and put the screws back in, very easy to change. I really like the fast way I receive a part from you.

Unscrewed 2 screws holding terminal ends of the element in place. Eased the element out, until the two AC power wires were exposed. Pulled off the connectors from the element terminals (pretty tight fit - needed pliers to remove one of them).

Slipped the connectors onto the new element terminals, and eased the element back int ... Read more o the oven wall. Secured the element with the two screws removed previously, and that was pretty much all there was to it. Closed the circuit breakers, and the element tested OK.

Overall, a no-sweat job. One thing, though: I squeezed the oven connectors tight before pushing them back onto the new element. They had loosened up somewhat after pulling them off. A tight connection here seems pretty important, as arcing and corrosion could occur over time if they're too loose.

Before you touch anything unplug the range or trip the breaker. Pull the racks out of the oven, it gives more room to work. Remove the two screws that hold the element and pull the element out about 2-3". Disconnect the old element. Before you install the new element check the wire and the connectors for age and heat damage. If the connec ... Read more tors are loose replace them (2 connectors @ $1.97 is better than a short in the oven). If the insulation on the wire is degraded (brittle, flaking, brown) consider changing out the wiring. This means opening up the back of the oven and that is another chapter. In most cases you can just re-connect to the replacement element and attach it back to the oven with the two screws. I ran the oven to 400 degrees to just check that everything was OK. Spent a couple extra minutes to check everything out and save yourself pain later.

Removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires and then replaced the new heating element by connecting the wires and then placing the screws back in. Was a lil difficult because this unit has no oven light and it required a flash light.

Moved the Appliance out unplugged it and removed the backing plate then Remove the Knob and unscrew the infinite switch then marking the 5 wires to know where the go on the new switch, removing and replaced it with the new one

The display would just go blank sitting idle or when using oven, oven and timer would shut off and display go blank. Just pushing on display it would come back. So I replaced the front oven control assy. Not that difficult to replace. But new unit does same thing? Really confusing to me, I'm now waiting the relay control board to rep ... Read more lace next along with heat sensor. Again removing wasn't to much trouble, of course Turn Power Off first. 4 screws to remove, kind of work it out away from relay board, remove connectors, plastic lock might break from brittleness, but it won't cause a problem. Remove mounting brackets and put on new assy, repl connectors, work back in to mount. When removing cover mark burner brackets as to FR, RR, FL,RL, the heat shield comes out, remove 4 screws, lower one side raise other and it comes out just fine. That's about it, I'll let you know how the relay board goes when I get it and if it fixed the problem.

The repair was simple; I removed just two screws, pulled out the wires, and slipped the two spade connectors off the original element. The repair was simply the reverse of the disassembly. The only thing to remember is to throw the circuit breaker before handling the electrical connectors. Other than that, it couldn't be any more strai ... Read more ght forward.

First removed the old gasket using a needle-nose pliers. Then placed new gasket by inserting the little clips on the gasket. Took 5 minutes. Great instructions from Repair Forum.

Removed and replaced above named parts, rewired.Be sure to tighten all nuts that secure wires. I believe this is what caused the problem.

I removed 4 screws and then lifted up the top it gave me access to the element I followed the direction that came with the element (very clear to follow) removed and installed the new element and it worked fine. Remember to unplug the stove if it is electric this is not in the instructions.

I Opened the top front panel, removed the control screws, pulled the control forward, took a photo of the wire locations, installed the new control and buttoned it up. Job was done and the oven works fine.

It was easy to confirm that I ordered the proper control due to all of the pictures you have illustrating the part on your ... Read more website - very good.

Incidentally, we needed the oven to roast a turkey on Christmas day. I ordered the part on Dec. 21 and received it on the 23rd, and had the oven working within an hour - great service.

flipped off breaker
Pulled the stove from the wall about 2 feet
Removed back cover (4 screws)
looked at existing switch - it was different than the new switch, but the instructions were spot on for the retrofit
I marked the back of the new switch with the retrofit locations of the wires
pulled off the knob
re ... Read more moved 2 screws from the front of the range that holds the switch
removed old wires using needle nose pliers
attached new switch re-using same 2 screws from the front
one at a time attached the wires to their proper location
pushed knob back on
reset the breaker
tested the new switch - all was OK
switched off breaker again
replaced the back cover
slid range back in place
Breaker back on
finished

removed back cover
removed wires
removed two screws and removed switch
replaced switch and two screws
replaced wires and back cover

Turned off the power at the breaker box. Removed the two screws, pulled the element out about 3 inches, disconnected the two wires, reconnected the two wires to the new element, inserted element back into place, screwed in the screws...all finished...works great! Delivery was super fast...just a great experience all the way around.

Being a woman, I first cleaned the oven. Removed two screws holding the element in place. Pulled element out about 3 inches and disconnected one clip attached to a yellow wire another clip attached to a green wire. Put new element in connected clips. Replaced screws.