606140 (2006-02) Husqvarna Lawn Tractor - Parts

This is a genuine OEM part made for Craftsman lawn tractors and mowers. Bearings are used to buffer moving parts from damage due to friction. They also stabilize directional movement. Bearings are high-wear parts and are changed regularly. This metal bearing is sold individually. Gauges, washers, rings, etc. sold separately.

The Push Nut is a black, metal nut, which can be installed with pliers and a hammer. It's used to secure parts in place in various locations on a variety of equipment. If damaged will not longer hold in place. Installation is rated as "Easy", but it will depend on the parts your are securing and the equipment you are using. Consult your m...Read moreake, model and diagrams to ensure this is the correct part. The part is sold individually.

E Ring Number 5133-75 is a black, metal ring for securing the position of other parts. If damaged it will become loose or fall off. Installation is rated as "Easy" and is done with a pair of pliers. Refer to your make, model and diagrams to ensure this is the correct part.

This OEM-certified washer provides support, spacing, and reduces friction between parts in your lawn equipment, typically working alongside bolts or screws. This washer has a thickness of 16 gauge and dimensions of 25/32 x 1-5/8 inches. A damaged washer will look deformed or cracked, leading to parts becoming loose or not fitting properly...Read more in your machine. When you remove a broken washer from your machine, you will need pliers or a wrench to loosen the bolt or screw securing it. Once the fastener has been removed, you can pry the washer with a screwdriver. It is important to know that this washer is sold individually. Before adding this replacement part into your cart, check your instruction manual to determine the number of washers your machine needs.

Made of high-quality metal, this hex flange locknut is designed for use with various lawn mowers and ride-on mower/tractor models and is sold individually. This locknut attaches to the end of the carriage bolt and is an important component to the axle assembly. This locknut has a 3/8-inch inner-diameter and is 16 threads-per-inch. To repl...Read moreace this locknut, you will need a wrench, and if there are multiple locknuts on your equipment, they may all need to be replaced.

This replacement v-belt is a genuine OEM sourced part. It is specially manufactured for use with riding lawn mowers. This is the the belt that is attached to the transmission pulley helping to drive the unit. Over time belts tend to wear out and stretch eventually requiring replacement. Inspect belts periodically and replace them as neede...Read mored to maintain peak performance. This part is made out of strong rubber material and it is sold individually. To complete this repair you will need a set of wrenches.

This metal square key is designed to prevent the rear wheel of your lawn equipment from slipping. Approximately sized at 3/16 x 2, it fits into the groove found on the axle and the hub of the wheel, ensuring proper alignment of the two parts. If the machine becomes hard to turn or maneuver or it makes a grinding or clicking sound, your sq...Read moreuare key may be worn out. Visually inspecting this part for bends and cracks can confirm this. You may also notice that the rear wheel is wobbling or falling off. A worn square key can cause damage to the wheel assembly of the machine, leading to costly repairs or even the need to purchase a new one. To prevent that, you need to replace a broken square key as soon as possible. Replacing the square key is a simple process. After turning your lawn equipment off and letting it cool down, you need to use a jack to lift the rear of it off the ground. Remove the wheel from the axle by using a socket to remove any bolts or nuts holding it in place. With pliers, you can then take the square key off the machine. This replacement part is sold individually and is sourced directly from its original manufacturer.

This replacement blade is specially made for use on riding lawn mowers and tractors. It is a genuine OEM sourced high quality item, it is not an aftermarket imitation. Usually two of these blades are used to cut the grass. Please note, this durable metal item is sold individually. To replace it you will need a wrench to remove the blade bolt.

It is an authentic replacement cap-spindle that is supplied by the original equipment manufacturer for use with Poulan, Ryobi and Husqvarna riding lawn mowers and garden tractors. It is an identical replacement for a missing or damaged cap that was originally installed on a new equipment. The cap is utilized to cover the spindle. Make sur...Read moree to check the appropriate diagrams of your model for the exact location and application of this hardware. This high-quality cap-spindle is made of durable plastic material and is sold individually.

This is an authentic replacement part sourced directly from the manufacturer. The return spring is commonly found in Craftsman lawn tractors and riding mowers. This part is made of metal, and is generally used to apply tension to the idler arm. You may require pliers when replacing this item. The return spring is available as an individual replacement part.

The screw with hex washer attaches to the pivot bracket assembly. This item is available as an individual replacement part. This genuine part is supplied by the original equipment manufacturer for use with Craftsman lawn tractors and lawn mowers. A wrench will be necessary during the installation of this item. It is made of metal and will require replacing if it becomes broken or stripped.

This lightbulb is supplied by the original manufacturer and intended for use in lawn tractors and riding mowers with a 12-volt system. It is positioned on the front of the equipment as part of the equipment lighting system. The lightbulb illuminates the area allowing for improved visibility when working in low-light conditions. The lightb...Read moreulb can fail due to various reasons, such as burnout, electrical issues, or physical damage. Once the lightbulb stops functioning, visibility will be reduced which makes it difficult to safely operate the equipment. Before you begin the repair, disconnect your equipment from the power source to avoid electrical hazards. Remove the bulb housing cover, and carefully unscrew the old bulb. Thread the new bulb into the housing and ensure that it is securely seated. Finally, reattach the housing cover, reconnect the power supply, and test the new bulb. Note that this bulb is part of a dual usage system, therefore ensure that you order at least two as each bulb is sold individually.