5TW4307SW0WS General Electric Washer - Parts

This drain pump assembly is for washers. Drain pump assembly removes water from the washer during the drain portion of the cycle. The assembly may include multiple parts; refer to your parts diagram for a complete list of parts included.

This water inlet valve assembly controls the flow of hot and cold water into your washing machine, ensuring each cycle uses the correct amount of water. If your washer isn’t filling properly, is leaking, or continues to fill even when turned off, the valve may be faulty and require replacement. The part is housed in durable gray plastic a...Read morend does not include a gasket. Installation may require basic tools and should be done with the power and water supply disconnected.

This is a manufacturer-made suspension rod and spring assembly for your washing machine. This suspension rod is one of four suspension rods that make up the entirety of the inner suspension of your washing machine, and if worn out or damaged, must be replaced immediately. If you hear loud or excessive banging noises from your washing mach...Read moreine, this and/or other suspension rods within the washing machine are worn out. This specific suspension rod is the left assembly, so the parts for the other side of your washing machine will also be required when replacing this one, considering they all wear at a relatively similar rate. This suspension rod assembly is sold individually, so it does not come with any other suspension rods.

This rod and spring assembly is designed to fit with washing machines and is made by the original manufacturer of your washer. It is a part of the washer suspension system that helps to stabilize and support the drum. The rod is a cylindrical plastic component that connects the drum to the outer frame of the washing machine. The spring is...Read more made of metal and provides tension and elasticity. The assembly is designed to absorb shocks and vibrations while the washer is running to help prevent excessive movement. If the assembly is damaged or out of alignment, the washer will be unstable and noisy. This assembly is designed to fit on the right side of the washer.

This is a mode shifter or shift actuator for models of washing machine. Mode shifters are designed to change the function of the washing machine motor, between spinning cycles and agitation, and is usually installed at the bottom of the washer. If your washing machine is not spinning or agitating during its washing cycle, or if it simply ...Read moredoes not start, this shift actuator is likely bad and in need of replacing. This shift actuator is made mostly of plastic, and features two holes to secure it with screws, as well as a single wire harness that connects within your washing machine. This shifter is an OEM part and is sold individually.

This is a clutch for your washing machine. The clutch is made of a white plastic material and is used within washing machines to engage and disengage the transmission during the wash and spin cycles, and ultimately help spin the basket of the tub so your clothes finish damp and not soaked. If your washer has issues with spinning or agitat...Read moreing, this part is likely broken or has worn out, and will need to be replaced. To replace this part, some disassembly of your washer will be required, and tools like a screwdriver and socket wrench will be needed. This clutch is sold as an individual and does not come with any other parts.

This drive belt is sourced from the original manufacturer for use in various models of dryers. It is a rubber belt that connects the motor to the transmission of the washer. It enables the drum to spin and agitate during the wash cycle. The belt is prone to wear over time due to the high friction it experiences. The belt may slip, become ...Read morefrayed or lose tension. If the belt is faulty, the drum will have difficulty rotating, you may notice loud banging or squealing sounds, and a burning odor coming from the washer. You can find the belt near bottom of the drum or towards the back.

This is a speed sensor for a variety of washing machine models. Speed sensors are used to monitor the speed of the washer drum and communicate it to the electronic control board to slow or quicken it. If this speed sensor is damaged or bad, it will cause your washer drum to rotate too quickly, slowly, or inconsistently. Replacing this sen...Read moresor will require a screwdriver and some minor disassembly of your washing machine. This sensor is an OEM part and is sold individually, so it does not come with any other parts or accessories.

Grinding, vibration, or poor basket movement can point to a damaged clutch spring, but other drive-system faults may cause the same symptoms. The spring helps the clutch engage during agitation and spinning. First inspect nearby pulleys, the belt, clutch surfaces, and mounting points for damage. Match the replacement to the full appliance...Read more model because similar springs may differ in length and tension. Disconnect electrical power and water before opening the washer, stabilize the cabinet, and wear eye protection when handling the spring. After reassembly, run an empty test cycle and stop if unusual noise continues.

Presenting the GE SCR 1/4-20, 2A SINULOC Screw, a key component for ensuring the optimal functioning of your washers. This robust piece, designed with precision by GE, assures a safe and snug fit to maintain the efficiency of your appliance. Constructed to resist wear and tear, this piece is sturdy and durable. Please adhere to all safety...Read more practices during installation to safeguard your appliance and ensure longevity. Experience peace of mind with GE quality, reliability, and efficiency when you choose the SCR 1/4-20, 2A SINULOC Screw. Make your washer perfect with GE precision.