5KSM193ADSMH0 KitchenAid Mixer - Instructions

My girlfriends' stand mixer failed when the accessory drive cap fell into the mixing bowl and jambed the beater, spliting the worm gear. The teeth on this gear are made of nylon and are molded to an aluminum center. This part is designed to fail in situations like this, saving the more expensive transmission parts. Following a repair manu ... Read more al I found online, I first removed the rear cover and pulled out the cord strain relief out from the base. Next I removed the drip cup from around the base of the planetary drive. I then used a pin punch to drive out the pin holding the planetary to the center shaft and removed the planetary. The unit was then inverted and I removed 4 screws holding the bottom cover to the gear case, and the 5 screws from around the planetary drive. The bottom cover was then lifted off. Three screws holding the worm gear bracket in place were then removed and the worm gear assembly lifted out. A small pin holds the worm gear to the shaft. I drove this out with a small pin punch and the shaft and worm gear were then removed. There is also a thrust washer on this shaft, and it's location is important. Make a note for re-assembly. The new gear was installed and the entire process reversed for re-assembly. A successful repair completed! My girlfriend would have replaced this $200 appliance, but I was able to repair it for less than $30 including shipping.

I removed screws in a sequence that I felt wouldn't further damage the mixer until I had it completely unassembled. When I found the broken worm gear, I went online to find a part. I found an exploded view, but the part numbering was old, and the salesperson couldn't tell me what the worm gear and bracket assembly consisted of, as I only ... Read more wanted the worm gear. After trying to drive the pin out of the assembly, and failing, I decided to back online and see if anyone else had a photo of the assembly. Luckily (and wisely) PartSelect,com did and that answered any questions I had. The price was better, too. Reassembly of the mixer was a cinch with the exploded view. It's working like new, and we're hoping for another 35 years of service from it! Thanks.

I removed the rear cap, decorative strap, and decorative ring. Next I drove out the pin holding the mixing head. I then removed the 9 screws holding on the motor/gearing portion. This facilitated removal of the gearing from the motor assembly. I next laid in the new gears and calculated what thickness of fiber washers were needed to h ... Read more old the gears in place. Reassembly was in reverse order of dissassembly.

1st I check if there is a burnt smell, there was burnt smell from the board phase. Check the motor brush. Surely enough they're at max (not touching the motor anymore). Replaced both parts, put everything back together. Tested it, it works like a charm. It's been working for the last 2 weeks now!

My kitchenaid mixer is at least 37 years old. Everything has worked fine after all these years except the screw cap was flimsy, still stainless steel, but not sturdy. So I tried to replace it , but was told it was too old and couldn't get the part. I contacted Part Select and found a screw cap from newer models fit perfectly and should ou ... Read more tlast me and the mixer, it is a lot sturdier than original one. It also arrived in 2 days, which was fantastic. Thanks guys

We:
tipped the mixer over on its side
pulled the old feet off
put the new feet in place and pounded them w/our fists
set it back up on its new feet
smiled

I actually didn't do the repair. I asked a friend who was a carpenter about what he thought was wrong with my mixer since it only had high speed which made mixing flour a snow storm. He said when his tools do that, it's the brushes. He ordered new ones and presto - my mixer works marvelously. He saved me from dumping a good mixer and $ ... Read more $$$$$$.

just took the unit apart and replaced the worn gear and bracket . Then took the old worn gear and bracket apart and replaced the worn gear . Then put the assy back together and now I have a spare

remove 6 screws for top of unit, remove gear assymble (23 screws), reassmbly and test it works great

unscrewed the screw holding the old brush. carefully removed the spring and old broken brush. we did have some of the old brush left inside, so my husband used a very thin drill bit to break it up. then carefully inverted the stand mixer to allow the broken pieces to fall out. then we were able to install the new brush. works great. yea ... Read more h!!

We followed the you tube instructional video. It was excellent with good advice that kept us out of trouble. My mixer works like new again.

first removed the dress ring by tapping it very gently.then drive the pin out that holds the beater plate on, now wiggle it off, then you can see the screws that hold the gear reducer on. remove them. take that off and you will see the housing that hold the worm gear. remove the 3 screws that hold it down . Now you will have to drive the ... Read more drift pin out that holds the worm gear in place, slide the shaft out then remove gear. reverse order to assemble

Took the old feet (5) off and put new on the Kitchen Aide, looks great. Stands high and your assistance on the phone, was so appreciated.

My early '60's Kitchenaid K45 mixer screw cap/base plate would no longer hold the bowl, so I looked for another. This item, though not an exact replica of the original, fit and works great. The design is better by being more stout than the original. Pretty straightforward installation: remove three screws, take out old base plate, install ... Read more new plate and screw down.

Very messy as there is lots of heavy grease inside the mixer and you have to fish out the blown gear parts. I vary glad I took shop class in High school as it preped me for the job. The machanical drawing you provide were very useful but you should mention the grease.

Mixer works just like new. and I got the parts in two days w ... Read more ith standard shipping. Pizza on Thursday and fixed by Saturday