59289679 (0001) Samsung Dryer - Instructions

I YouTube it and there’s a step by step process on how to do it, took maybe 30 mins. If I can so can you

YouTube, YouTube, YouTube. I YouTubed many videos on how to take a dryer apart to reach the drum support roller and axle. After watching numerous videos, I settled on one that had my exact model of dryer. For my dryer, previous inputs said I needed two rollers to for my model. That is not the case. My model actually has 4 rollers, 2 in th ... Read more e front and two in the back. I ordered 2 initially but only needed 1 thankfully since only one roller was bad. Keep it simple stupid is how I got it done. Dryer's are pretty simple machines mechanically. Don't trash your noisy dryer. We bought ours in 2014 and it only recently started giving us issues. This is after 2 moves and being run daily for a family of 6. I'm glad I found partselect.com. They saved me a ton of money.

Watched a video on utube, how to repair my 16 month old steam dryer. The hardest part was laying on my belly holding the spring loaded tensioner and slipping the belt on around the blower housing. Only cost me $23. Winning!

Dryer would not start but electronics were working.

Pulled top of dryer off; noticed the belt was loose but not broken.
Went in through the back (1 screw and removed the exhaust pipe/plate); noticed the wheel was broken and thus the belt had fallen off.

Ordered replacement wheel/arm.
One screw to remove ol ... Read more d one, one screw to install new one...tentioned the belt. Dryer was good as new.

Samsung had no servicers available, after over 3 months calling and sending photos and signing papers they sent a refund. Never any advice on repair from Samssung. Saw a video by JEFF OSTIROFF that lfor disassembly and location of heating parts. Gor $40 Samsug service manual that was rather useless. Disassembled and tested thermostat, T ... Read more hermistor, and heat element. Appeared that HI-HEAT thermistor was open circuit all others OK. Sent for new one, arrived damaged insufficientlyb packed Tested original again out of appliance, tested OK. Got replacement for damaged thermistor and put it in, reassembled and IT WORKED! Notvsure if original thermistor was intermittant, or connection problem was the fault.

I ordered twice from this site. the thermistor was the first order, the fuse was the second order. Turns out the thermistor sent was the WRONG one. When I reassemble the dryer, after 20 minutes the thermistor sent burned up to a crispy chard. The ohms on the wrong part was 12ohms. per the dryer diagnostics the thermistor should have been ... Read more =<1 ohm. I put in the original part and it worked. The fuse did the trick. the thermistor, not so much. Lesson to be learned is to not rely on this sites parts compatibility information. Look at the specs for your dryer from the manufacturer.

Cleaned the sensors from inside the drum with alcohol and that did not work. Ordered two sensors. Lift top cover. Remove screws on each of the front side that secures front cover. Unplug door sensor and pull front cover towards you and lift at same time removing from frame. I own dogs and immediately noticed dog hair and surprisingly ... Read more lint all over the place. Remove the screws from the lint trap. (Theres one you access from inside the drum.) Unplug your sensor wires. Remove lint trap. The sensors simply push in/out. While I was in there I removed the cover for the lint tube and cleaned it out good. Lint had started to gather around the fan. Reverse your process and your done. TIP: Keep your screws orderly as you unscrew them. If you have this problem, just a good cleaning of hair, lint, dirt may do the trick as it essentially packs around the plug of the sensors. I had already ordered my sensors so I just put them in. I took my time and cleaned good and it was about an hour. It could be done in 15-30 minutes easily.

I pretty much followed the provided videos, but didn't remove the drum. That seemed a bit much. I was able to get the heating element out, and replace the Thermal Fuse and Thermostat. Dryer runs and heats like a top now!

After viewing many instructions on how to replace a broken drum drive belt on UTUBE and the video you sent me the project was completed with no problems and with ease.

However, I did discover large amounts of lint caked to the bottom of the lint screen housing just beyond the filter screen. There was minimal lint on the lint ... Read more exhaust fan blades and no lint in the exhaust ducts.

I didn't recall seeing any video instructions drawing attention to potential lint issues, it just made good sense to clean the entire system while it was apart . At first I saw no major lint problem.

However, after removing the lint screen and placing a vacuum cleaner wand to the bottom of the lint screen housing (the bottom is not easy to see) my vacuum cleaner hose became clogged three times. I realized there was a major lint issue isolated to this area.

Many of the on line complaints focused on parts not properly fitting their dryer. they had to modify the parts in some way to fit or operate or they had to return them for other parts. Just think of the time wasted and the lack of use of their dryer.

I called and talked to a tech. Gave them my model number and the tech located the correct OEM parts for my dryer. I paid the extra money for OEM parts because I wanted my dryer fixed and restored to service in the least amount of time.

Outside the discovery of the not so obvious lint issue, the repair project was easy and the dryer was restored to full service with minimal down time.

Thanks for all your help and fast delivery service.

A month prior to this repair, I took the dryer apart, cleaned the clogged lint out, and replaced the thermistor with a cheap aftermarket part. It lasted a month. Bought this more expensive OEM thermistor, hopefully of a better quality. Realized that I could have gotten to the thermistor from the back by simply removing the vent pipe an ... Read more d carefully reaching through the vent pipe hole to take out the thermistor. Did that this time instead of taking everything apart. Also bought an updated lint screen (aftermarket part). It has better mesh although it doesn't fit quite as perfectly as the original. So we'll see if the OEM thermistor lasts longer. The repair time was mostly spent moving the washer and dryer within a fairly small laundry room. The air lifter really helps.

I removed the dryer top and saw that the belt was intact. (I had suspected the belt or something stuck in the exhaust fan or somewhere.) I watched a few youtube videos and took off the rest of the top plates and front door and inner structure that held the barrel. After i inspected and cleaned out the fan blades and exhaust areas, I looke ... Read more d at the pulley rollers (motor and idler rollers). The idler roller looked a little melted and chewed up. I replaced it with the new assembly. Also replaced the belt. Putting the barrel and new belt back on was harder for me than the videos indicated because the spring was very tight and the area to put my hands was small and didn't give me enough leverage. I eventually got someone to give me the third hand pulling the idling roller a little further over and the belt was back on. It didn't take me long to put the whole dryer back together. It is running fine now.

These are not instructions as much as warning that although it is a one-person job, the idler pulley assembly is not as easily manipulated with the barrel there. Doing the fix was straightforward: one screw holds it in place. The men in the videos seemed to have no problem with easily replacing the belt, but I needed help with the tight spring. Perhaps now that I've done it once, I could figure out how to reach around the barrel and yank the roller enough to replace the belt, but with the extra hand it took seconds and was super easy.

this site is amazing. I went on the website, put my model number in and they had suggestions for what might be the problem. “Dryer making a noise?” Click here. I bought a new tension pulley and belt. I watched the videos on how to replace them and the step by step instructions were spot on. Turns out, the old belt had frayed! I probably ... Read more didn’t need to replace the tension pulley but I did it anyway. The sound is gone, and I felt like a genius for probably a week or so. The last repairman charge me hundreds of dollars to replace the rollers, but now I know how to do it myself. This site is awesome.

Separated the outer door from inner door, removed glass globe. Replaced the seal

Reassembled

NECESSARY REQUIREMENTS TO DISMANTLE AND TAKE OFF DRYER CASING USING SCREWDRIVER AND NEEDLE NOSE PLIERS TO REPLACE THERMAL FUSE LOCATED ON THEHEATING ELEMENT CASING.TOOK ME HALF HOUR REPLACED PART AND PROCEDED TO PUT EVERYTHING BCK IN PLACE.PLUGGED BACK INTO SOCKET .whalla IM UP AND RUNNING AGAIN.DIFFICULTY RATING 1 TO 10-3.thanks 4 your s ... Read more upport this was not difficult or hard just required TIME & PATIENCE. Thank u once again.THIS SITE IS THE GREATEST.

I removed the dryer vent and cover to take a look at the inside of unit. Then I saw that wheel on the pulley was damaged and belt was tangled up. I simply replaced the pulley and placed the belt back. Samsung advised that I replace the unit, but myself $800+ on a new unit.