592058 Briggs and Stratton Engine - Parts

This OEM Seal-Oil (PTO Side), also called the Oil Seal, is a Black, Nitrile Rubber, 2/14 O.D., individually sold part which is installed using a Seal Puller. Customers rate the installation difficulty as Medium. This part provides a seal around the crank shaft and engine block. When installing onto the engine block around the crank shaf...Read moret, use something that makes contact around the entire seal, like a large socket or pipe, and tap into place evenly, ensuring that the housing is clean and dry. If the part is broken, likely due to fatigue, there will be leaking oil, and this part should be replaced using the model number on the original part to confirm it is the right fit for your model.

The Oil Seal is a manufacturer-approved rubber part which provides a seal between the crankcase and crankshaft by attaching around the axle shaft on the crankhouse housing. Installation is rated as "Medium" difficulty and requires a screw driver, wrench set and seal puller. A broken seal will cause a leak, and the part must be replaced. R...Read moreefer to your make, model and diagram to ensure you're choosing the right part. This part comes in black and gray.

This OEM exhaust gasket in lawn and garden equipment creates a seal between the engine block and the muffler or exhaust pipe so that exhaust gases do not leak. This is 3.30cm in diameter and 6.35cm in length. Your machine may have a loud hissing or popping sound coming from the exhaust area if the gasket was faulty. You may also notice th...Read moree presence of black soot around the gasket or the exhaust. Your gasket needs to be replaced if it appears worn or deformed. Otherwise, your machine will experience exhaust leaks. To detach the gasket, remove the fasteners that secure it using a socket or wrench. You can detach the gasket from your machine afterwards. Please bear in mind that this replacement part is sold individually.

This item is an authentic OEM replacement part that is intended to be used with small engines from Briggs & Stratton. The breather tube is used to guide the direction of excess gasses and fluid that escape the engine from a higher level of internal pressure. The breather tube is a single item, please see the model diagram for related parts.

The Seal-O Ring, also known as the gasket, is red in color, made of rubber, and is an OEM part that requires some skill to replace. This part is designed to create a seal between the carburator and manifold, to prevent air from entering. If your engine loses power, creates a hissing noise, or if the gasket appears damaged or your engine r...Read moreunning improperly it may be time to replace the part. If you run the engine and spray the outside of the carburator with soapy water, you can test whether or not the gasket is leaking by listening to the sounds produced. If the sound smooths out then you've found your leaky gasket. Damage may occur over time, especially if the part dries out, and make the part appear stretched or worn out. When making this medium-difficulty repair, make sure the new gasket is fitted properly between the carburetor and intake manifold.

Genuine OEM replacement part used on a variety of Engines. This item is made with Composite Material and it is sold individually. Its purpose is to make an air tight seal so that no air/oil leakage occurs. Over time this gasket will deteriorate and will need to be replaced. The gasket measures .015 Thick.

This manufacturer-certified Gasket-Intake, more commonly known as the Intake Gasket, is a gray, 3 x 2 inch, individually sold part which can be installed using a Wrench or Socket and a torque wrench. This part provides a seal between the caburator and intake manifold, and can be easily installed. Just ensure you are tightening to the manu...Read morefacturer specfications when repairing this part. If your engine is getting more air than fuel and appears under-powered, it may be a sign this part needs to be replaced. Try spraying a mixture of soapy water at the base of the carburator at the intake manifold with the engine running, and if the engine runs more smoothly then you have discovered the problem.

This is a genuine OEM part. The Briggs & Stratton valve seal is used on many lawn tractor machines. The metal part stops oil from moving into the cylinder from the valve stem. This item is often fastened to the intake valve and the valve keeper. A screwdriver, socket set and wrench set are required for the installation. The metal valve seal is sold individually.

This item has been sourced from the original manufacturer to be used with lawnmower engines from Briggs & Stratton and Toro. The o-ring is used to seal the connection between the intake manifold and the cylinder head assembly. This o-ring is available as an individual replacement part.

This is a genuine Briggs and Stratton, Toro part for use with lawn and garden equipment engines. The crankcase breather valve opens to relieve pressure in the crankcase. The most common reason for replacing the breather is when the small engine runs poorly. This part is sold individually. Here is a list of tools that are needed to replace...Read more the breather valve a flat-head screwdriver, hammer, 7/16th-inch socket, 3/8th-inch socket or nut driver, Phillips-head screwdriver, 5/16th-inch socket or nut driver, 3/8th-inch socket or nut driver, pliers.

This item is a genuine Briggs & Stratton replacement part that has been sourced from the original manufacturer to be used with small engines. The gasket is used to seal the connection between the cylinder and the head. This item is available as an individual replacement part.

This part is an OEM sourced directly from the manufacturer for use in lawn tractors made by Briggs & Stratton, Murray, and Toro. The star screw attaches to the connecting rod and is made of metal. It might require a torx screwdriver to replace this part if it becomes stripped or broken. This item is priced as an individual replacement.