58714012404 Kenmore Dishwasher - Instructions

Took the roller out of the package, snapped it into place. Less than 15 seconds. Works good as new.

First I opened the door all the way. Second I reached down to the bottom gasket then grabed it on the right end of the seal that is on the right side of the door. Then I pulled the end outward from the bottom of the door toward the heater coil in the bottom of the washer. It came out real easy. You see it just snaps into a little plastic ... Read more groove under the door. I then cleaned up the area for food and soap particules. I then placed the new gasket in place by lining up the notch toward the right end with the piece of plastic that encloses the right end of the plastic notch on the bottom right end of the door. Then push it in untill it stops going into the notch. It snaps in but does not make a snaping sound. It just won't go in no more.

I removed old tub gasket, which the door presses against to make a seal, and put the new one in. Flat tip screwdriver was used to gently press gasket in.

Received the part 3 working days after order. Part was exactly like the original.
Removed the door. Slipped off old gasket and replaced with new gasket. Replaced door and tried rinse cycle. Worked perfectly.

With the door wide open and lower dishtray out, I pulled the old gasket out of its channel. I cleaned the channel with a rag and replaced it with the new gasket. It needed to be trimmed about an inch in order to get the door to close properly. Took me about 5 minutes. Then I removed the old bottom door gasket. Just grasped the plasti ... Read more c edge showing while the door is completely open. Pull outward with fingers moving toward the heating element. Cleaned this area also. Took the new gasket with notch on the right hand side of the dishwasher and pushed it into place. If you get down and look closely, you can see where the notch hooks up. The rest of the piece just slides in after that. Hasn't leaked since! No leaks AND no service call fee. Parts came super fast! So glad I found this website. I'm a housewife, you can do this!

The tub perforations at the heater leaked and water dripped onto the fastening nuts and the electrical connections. I ordered a new heater element and it did not have the necessary nuts to fasten it to the tub. I had to go back and order them separately. The original nuts are very unique and cannot be substituted for.The manufacturer shou ... Read more ld send them with every heater element because this leaking problem is very prevalent on these machines.

Reading the instructions posted, I realized that I only needed to remove the two lower screws on the inside of the dishwasher door. The lower front panel then came off easily. I unplugged the power to the dishwasher. I then removed the six screws holding the dispenser in place, and when loose I unplugged the two wires (I used a flat blade ... Read more screwdrive to pry them a bit then they slid off -- note the red one was inside, lighter one outside). I put the new part in, put in all but the left screw with the hook. I then plugged the wires in, and fastened the left screw with the hook positioned around the wires. I put the panel back on, fastenet the two screws that hold it in, and plugged the dishwasher back in. It's working beautifully. All in all it was about 20 minutes.

**** A stubby Philips screw driver will save you a lot of headache taking the two retaining screws out that hold the drain pump assembly to the hanging bracket *** An inspection mirror was also helpful trying to locate these screws.

I thought the pump impeller vane was possibly broken because the pump would not drain the dis ... Read more hwasher but it would energize and make a loud clicking/rumbling noise.

1) Drain water from the dishwasher. I used a piece of tubing and siphoned the water out. Remove front cover plate.

2) Turn off breaker and dsconnect two wires going into pump.

3) Remove the pump inlet. I kept the 4" rubber jumper piece attached when I took the pump out.

4) I had to disconnect the wash water feed line to be able to reach the hose clamp on the pump outlet.

5) Loosen hose clamp on the pump outlet if you can reach it, otherwise remove the two screws that hold the drain pump assembly in. There is one screw on each side of the pump. I used an inspection mirror to see the screws. I had to use a stubby Philips head screw driver to take the screws out.

6) Wrangle the drain section out and finish taking off the pump outlet hose clamp. Install new pump and work backwards to put it together.

When I pulled the pump out I found the impeller to be complete (not broken as I had thought) and I saw it had two small steel balls that sat in grooves. I think the two balls and groove act as a safety detent and disengage the pump if something big gets sucked in. I pushed down on the impeller and everything snapped together nicely. Since I already ordered a new pump and I had everything taken apart already I installed the new one but I think I could have just used the old one.

Hope this is helpful to someone else. Washer has worked fine since.

The strip comes right out when you pull, there is a space to grip it on the left and pull it out. The notch goes on the right side when you put it back in; it only goes in one way. I didn't get it all the way in the first time and closed the door; the gasket came right out. A clear sign that I had done something wrong! So I put it in ... Read more again, this time pushing it as far as it would go. It went all the way in and stayed. It doesn't click or anything, but you can kind of feel when the notches all connect. Also, it doesn't slide right out again.... very easy!

Unplugged the dishwasher. Closed and disconnected the water supply. Removed two screws that attached the dishwasher to the countertop. Pulled the dishwasher out from underneath the countertop. Laid the dishwasher on its side to access the bottom. The high limit thermostat had shorted out and showed signs of electrical burn. I removed th ... Read more e high limit thermostat by unscrewing the single screw that holds it in place. I then pulled the two electrical terminals off the high limit thermostat . One terminal (i.e. small electrical plug connecting electrical wire to high limit thermostat) was burned badly. I cut it off the wire and attached a generic terminal bought at local hardware store (six for $3). The other terminal was fine. I plugged the new high limit thermostat in and attached it with the single screw to the dish washer. Put the dishwasher back in place. Test ran dish washer and dishes came out shiny, clean and dry. Done.

All I had to do was replace the spring and retainer on the side of the dishwasher which amounted to pulling it out far enough to reach the eyelet that the hook went into and then stretching it to the retainer attached on the other end. I really like partselect, I have done some things in the past and they are very helpful on the site and ... Read more on the phone and I would recommend them to anyone and I would not normally do that unless it has been an excellent experience.

Thought the problem was a faulty door gasket (there was a gap in the middle of it) so I ordered new(new one had a gap also) replaced it anyway - maybe it was worn out? Still leaked! Had to sit and stare at it and cycle it through. finally realized the spray arm had a hole in the end that was spraying directly into the gap in the door gask ... Read more et. Hot glued the hole and it stopped so I bought a new spray arm - no leaky!

It took less than a minute to remove the old bottom door gasket - it pulls right out. You wouldn't think the part looks the way it does (a 1.5 inch wide plastic strip that runs the length of the door with rubber gaskets on both ends) but have faith. Trust the diagram/picture - it is the correct part and will fix the leak. The new gaske ... Read more t arrived within a couple days of ordering and was simple to install - no tools. It slides into place in less than a minute and is held in by friction. Problem solved and no more leaks. For under $12 (parts and shipping) I had my dishwasher fixed. A service call by itself would have run $75 - just for someone to show up at the house, and then probably another $50 for parts and labor to install. My wife made the comment "Even I could have fixed that". A very simple and easy repair - you can do it!!!

My friend bought a used dishwasher at a garage sale, the previous owner had thrown away the drain hose because it was "nasty" they said....remember it could have been cleaned. When I went to install it, I removed the old washer, and discovered that the old hose would not fit on the replacement dishwasher. I went to the local repair shop, ... Read more armed with the model and serial #'s. they searched and searched their books and could not find the hose part number. they said "good luck" when I left...I went home and looked up the model on your web site, ordered the hose, and in 3 days had the dishwasher installed and running in about 30 minutes...thanks for prompt shipping.. I couldn't believe it arrived so soon...Mowerman

removed the remnants of the old wheels and popped the new ones on....simple

Got to say, I was pretty amazed that I received my order the following day! You guys are wonderful!