5605 - Instructions

I used the other 4 posting as a guideline but found that what wasn't mentioned here was that the disassembly/re-assembly instructions are actually located inside the washing machine behind the control panel (wish I knew that before I started doing it on my own).

After removing the control knobs (temperature, cycle, etc.), unscr ... Read more ew the four screws and lift the control panel off. Underneath the panel, there was a folded up wiring diagram that includes assembly instructions on the back.

Like others here, everything went smooth until I tried to get the Hub Nut (PS271505) off. No matter how hard I tried turning or hitting it (or the wrenches), it wouldn't move at all. I followed the other people's advise here and ended up taking a hammer and small chisel to the side of the nut. It's an aluminum nut so it cracked pretty easily and was easy to remove after that. Take my advise and just break the nut off if you are having any sort of difficulties getting it to turn. It's worth the extra $11 to just buy a new one!

I loosened the 4 screws that hold the motor and clutch in place. Removed the motor and clutch and turned upside down. Removed the retaining clip. Pulled the old clutch off (does not come off very easy). Stuck the new clutch on and replaced the retaining clip. Slapped it back into the machine.

First I removed the agitator. The shoulder screw on top of the air bell was almost disintegrated, but after soaking with penetrating oil and a large channel lock pliers I removed the shoulder screw. Next, the air bell required a bearing puller to remove it from the agitator shaft (with force application to the agitator shaft from above) ... Read more . After two days of soaking with penetrating oil, heating with a hot air gun, and countless attempts with a pipe wrench and sledge hammer the 1 11/16 nut was not moving. I drilled down along the flats of the shaft and dug out as much corrosion as I could and filled the cavities with penetrating oil. Next, I drilled down at an angle (so as not to gouge the centering taper of the spinner hub) into the nut in order to relieve some stress - no success. I ended up using a chissel ( blade and flat round ) to break pieces of the nut away which was quite brittle. After removing about 1/8 of the nut's top and tapered portion, it began to turn out with a pipe wrench. Next, the spinner would not lift out off the shaft, so I had to remove the entire tub and transmission assembly (but with the spinner basket attached) as instructed by the paper stored within the control panel. I removed the tub support bracket and motor assembly and the pulley off the transmission (pieces of the brake pad fell out). Using a 2X6 piece of lumber, I fabricated 2 semi circular pieces to fit within the 20 inch diameter of the spinner basket and secured their position with another piece of wood. I attached eye hooks to the wood and with rope,hung the entire assembly over an I beam with the transmission in the 5 gallon bucket and the tub suspended only about an inch above the bucket. I hammered on the agitator shaft until the tub and transmission fell the inch as it separated from the spinner basket. After this, it was just cleaning the areas receiving new parts. I did use a sealant around the new tub seal edges and bottom when assembling. Other than having to tap 1/4- 20 threads in the new transmission brake flange (new part had no threads in the holes) the reassembly went fine. I did have to retighten the new 1 11/16 nut after the first use because the new brake pad really stopped the basket from spinning, but the momentom loosened the nut after 3 loads of wash.

Removed front cover, lifted lid. Unnapped the broken tub cover pulling the tub forward to allow the old cover to clear the rear of the housing/top. Installed the new tub cover by once again doing the same thing and carefully snapping it into place. Reconnected the rubber sping offloads, lowered the top and reinstalled the front cover..rea ... Read more dy to run.

Removed timer knob clip and installed new dial and timer knob

First cut off both incoming water supplys. Next remove the water hoses to the inlet. Then remove some of the screws that are holding the back panel on that will give you access to the inlet plate remove those screws and that are holding the inlet in. when you remove the inlet mark the wires take of the water hose and remove inlet now do t ... Read more he opposite to assemble There was no Rocket Scientist needed and the funny part $12. cheaper than literally going around the corner to the appliance store Thank You and my wife thanks You

I loosened the four nuts holding the motor in place, slid the motor toward the tub to slacken the belt enoug to remove it, then replaced old belt with new belt, pulled motor back in place until belt was tight, then tightened the four nuts holding th emotor in place.

Used the repair instruction paper behind the washer control panel and used the online parts diagram. Also the online responces from other customer repairs gave me the idea to take a small pipe wrench (with a sock over the bottom of handle) and tap it with a 10 lb sledge hammer to remove the alumium hub nut. *** It is a backwards threaded ... Read more nut **** I did not know I was going the wrong way until I looked at the new nut and noticed it's reverse threaded!!! After that it was just taking everything apart and putting it back the way you found it.

I followed the instructions provided by GE that were stored in the control section of the washer. Removing the hub nut was a huge pain. It took Liquid wrench, hammer, pipe wrench and patience to remove it. Other than that it was fairly easy. I didn't like the way the tub seal fit so I used some silicon gasket making material to help make ... Read more sure the seal sealed good against the tub.

Based on other research, the location of the leak indicated that the main tub seal needed to be replaced. I took the washer apart before ordering new parts in case I broke other parts in the process and to be sure I could. I ended up having to cut off the Agitator Coupling and really marred up the hub nut. Those were the hardest 2 pieces ... Read more to remove since they had corroded badly after many years of use. I had to use a pipe wrench and a hammer to remove the hub nut and a hack saw to get the agitator coupling off (air bell).
$68.00 and 2 hours later, the washer no longer leaks.

took motor lose and belt lose first, then took pulley off from the tub shaft, then made a big mistake, I took and pulled the lower shaft seal. lucky I had a pan to catch the oil about half a gallon. After that I could not find away to put oil in the gear box, so I took the drum out and that didn't work but it was a good thing I did becaus ... Read more e the inside drum was rusting so I spend money on the seal for nothing. Had to buy a new washer. If I ever did it again I would turn the whole washer up side down so the oil could not run out and I would put the oil in the hole where the seal was. lot of work for nothing.

went very well thank you

In my case the rubber bonded to the agitator coupling had stuck inside the agitator cover (plastic part that comes in contact with clothes). The metal part with the splines could not be removed by gripping with pliers. A pulling tool needed to be used to remove the tool. I used a valve spring compressor tool for overhead cam engines, b ... Read more ut any pulling type tool with a center bolt and jaws that will fit between the rubber seal and the bottom of the agitator coupling would work. After removing metal part of coupling from agitator shaft and cleaning up the rusted teeth on the agitator shaft that caused the difficult removal, I pried out the rubber part of the agitator coupling from the plastic agitator cover by inserting a screw driver from the top hole in the agitator cover and getting it under the rubber to separate the toothed parts of the rubber from the matching grooves and then pushed it out the bottom of the agitator coupling. Then came the difficult part of the project - inserting the new coupling. I found the instructions that came with the new part very unrealistic and was not able to simply wet the rubber on the new coupling after installing it on top of agitator shaft and then push it into the plastic agitator cover - it simply would not go down more than 1/8" in the cover. If you attempt to do this job using the method described in the instructions you will likely end up with a damaged agitator, or cover as you will likely resort to hammering the cover on which is not recommended because of shock to agitator teeth. In my solution this is where a long bolt, 2 large diameter washers that the bolt fit through, several nuts larger than the bolt diameter and finally a nut that fit the long bolt came into play. Using these parts and a socket set with several long socket extensions I used the bolt, washers and nuts to draw the agitator coupling into position in the plastic coupling. This worked extremely easily once all the parts were in the right place and put no stress on any of the parts being assembled. To do this, first I installed the new agitator coupling on the agitator shaft - making sure it would remove fairly easily before continuing, then I pushed the agitator cover over the agitator coupling as far as I could to get it connected well enough to the agitator coupling so that when I pulled the agitator cover back off the agitator shaft the coupling would come with it (still in place with the rubber teeth from the coupling started in the corresponding grooves on the inside of the cover). With the agitator cover removed I placed a washer that was wider than the top of the agitator cover onto the long bolt (the bolt must be about 8 inches long) and then passed the bolt through the hole in the top of the agitator cover, through the splined hole in the agitator coupling (the bolt must be small enough in diameter to fit through the agitator couping hole). With the bolt and washer pushed all the way down on top of the agitator cover I turned the cover over and placed it upside down on the floor so that the cover pushed down on the washer and bolt and held them in place. I then used an extracting tool (something with little claws that protrude or retract) to lower first another washer large enough in diameter to cover the diameter of the agitator coupling bottom and then several nuts larger than the bolt diameter onto the exposed end of the bolt that comes out on the other side of the agitator coupling inside the long narrow tube of the agitator cover. Once I had enough nuts in place to leave only enough threads on the bolt for the washer and nut that fit that bolt, I set the nut on the end of the bolt and used the correct sized socket with several long socket extensions attached to it to hand tighten the nut onto the end of the bolt. Then securing the head of the bolt with a wrench to keep the bolt from turning, I placed a socket wrench on the extensions and socket that covered the nut and then tightened th

Finding the disassembly instructions in the control panel was very useful. After disassembly and inspection obviously the transmission had lost oil and deteriorate the belt and actually threw it off. Finding your web site was very helpful. The exploded views parts catalog were great! We had it rush shipped. It was great to speak ... Read more with a representative on a sunday was excellent. The rep was knowledgeable and we concurred on which part were needed. Tracking number was correct via e-mail but only rec'd tracking number for one of the two packages which was stressful at the fedex office at pick-up. All items were rec'd on time assembly was straight forward. The basin retainer nut came loose after 5 loads and made a terrible noise. I applied blue loctite to nut and reinstalled. Seems to be working correctly. Bought an extended warranty which added 4 yrs. Washer failed 2 months after warr. Expired. Figures!! Great experience with partselect thank you.

first use a puddy knife to remove the front cover – slide the puddy knife in the front upper left than right corners where the top meets the front of your washer they are push in clips that hold the front cover (they are not easy to damage)
second pull the front out than up of the bottom clips, there is the rods with a tube assembly ... Read more is either black or yellow that hold the tub up
remove the 2 screws holding the top they are near the clips you used the puddy knife on
lift the lid about 4 inches and you will see how it works, at that point with the replacement part in hand it is self obvious what to do replace the rod.
When done try the washer and if it works, if so put the covers back on.
The shock of it all is watching the natural violence your machine goes through just to wash your clothes